nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello,
I have been trying to setup timer counter for nrf9160dk using the sample I have attached but for some reason the timer value is always read as 0. Not sure if the...
Hi
We are thinking about migrating a project to the nRF52805. One of our concerns was that the nRF52805 may have no "legacy" UART and only supports the UARTE, which is much...
Hey There,
The problem I have is the following:
I am able to open a Port via Putty and C# Script. I set it up like I found it in the docs. ( https://developer.nordicsemi...
Greetings,
If I send empty line (CR or CRLF) to the modem AT port, modem freezes.
Firmware version: 1.2.1
AT%SHORTSWVER %SHORTSWVER: nrf9160_1.2.1 OK
User application...
Hi,
I have developed succesfully an HTTPs client but I am facing a problem related to a relatively long response from the server when I issue a GET request. After the GET...
Hi,
When I try to update the modem firmware I get this error Errorcode: CouldNotCallFunction (0x9) Lowlever error: Unknown value (ffffff24). See attached picture bellow...
I have a issue with nrf21540 in the Transmit state after the Receive state with using of GPIO for control Transmit / Receive switch.
I'm doing next steps for reproducing...
Hi,
I am trying to use the thingy91 to publish some sensor data to an Azure IoT Hub, I've tried to look at mqtt_simple and modified "asset_tracker" application but I couldn...
Hi Team,
This Query is regarding HF frequency Crystal settings, how to configure the nRF52840 Evaluation board to different frequencies. Actually we need to test the crypto...
Hi there,
I'm attempting to link in a static library archive to my nRF52840 targeted project and receive the following error: Exception table sections and plain sections...
when I use Jlink viewer for tracing, found a fatal error:
1 code:
static void lfclk_config(void) { uint32_t err_code; NRF_LOG_INFO("enter lfclk_config"); err_code = nrf_drv_clock_init...
I have been playing with the nRF5340 and specifically the HCI-RPMSG.
I have looked at these files below. They all worked when programmed in the nRF5340.
When viewed in...
Folks,
System Info : MacBook Pro (10,1; 15" Retina, Early 2013), Running macOS 10.15.6 "Catalina", with 500GB SSD, formatted with APFS, into a RO system partition and a...
I've made a circuit using the NRF8001 but slightly deviating away from the original PCB example. I'm getting the device to go into "Advertising Started" but I can't pick up...
hello Nordic
i have s SOM which i want to use nrfutil in it for FDU via UART of an application i have on nrf52832, s132 v7.0.1
i have the bootloader flashed with the...
