Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Good morning everyone,
I am facing a weird problem concerning the use of the UART service.
I am currently using the NRF52832DK to develop an application. In a nutshell...
Hi Forum,
I am working on nRF52840 THREAD sleepy node and facing an issue in deep sleep mode. The current consumption in deep sleep mode is more-around 60-70 micro Amp...
Hello guys!
Are there any difference in using FDS library with a nRF52832 or with nRF52810?
I will explain.
I'm using a FDS for writing/reading to flash for 2 months...
(I've seen several other posts mentioning similar issues, but many of them haven't resolved or found a solution that seems to apply in my case.)
I have a custom board that...
Hi,
I have a simple and basic question. it may be chilly. the internal flash memory can store the data, but the question is it has stored as byte per address or word per...
I am using a nRF52840 chip in a custom board. I will be using all the SAADC channels, as well as 4 SPI connected ADCs.
The board itself will likely be powered for days at...
Hi !
I am using NRF52DK and I want send some daat with BLE. I have to send 800 bytes in BLE by packages of 25. So I tried this :
BUT when I look my uart terminal, I...
Hi, DevZone,
I am trying connect nRF52480 Preview DK and an Arduino UNO CAN Bus shield.
What I did is:
1) I directly hook CAN Bus shield on the top of nRF52480 Preview...
Hi Nordic,
I started from an empty project with peripherial control first, the code size is about 12KB. Then after adding peer manager and related code(fstorage, fds and...
Hello,
I build a custom board with Nrf52832 , to drive Relays , all works without load , no problem for drive the output.
When i put a load sometimes my device disconnect...
what are the total number of devices that can be connected to nrf24 ?
I would like to make one transmitter and rest of all as recievers without acknowledgment will it be...
Hi,
We are trying to use GPIOTE / PPI to turn a MOSFET on A microseconds after an event clears a timer and to turn it off B microseconds afterwards.
It is easy to do...
I am running into an issue with the Fstorage Library with SDK14 that I did not have using SDK12.
When I am not connected to BLE I can erase and write flash with no issues...
Hello,
I am trying to make BME280 sensor work with nRF51 DK. I just need temperature readings. So i searched if there was some examples using this sensor and i found this...
