In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
I am looking for the third party nrf 52832 BLE module in which i need following configurations,
Size is less then 9mm*9mm
Chip antenna or PCB antenna
GPIO pins atleast...
Hi!
I would like to completely isolate the nRF52840 on the Preview-DK (2017.32) on hardware level.
Scenario
I would like to power the nRF IC with the external supply...
Hello, I'm new to Nordic boards.I would like to measure the bit error rate for a BLE link using nRF52840.
Is there any way of modifying any of the existing examples to add...
We use iOS nRF Connect primarily for DFU updates and find a real annoying issue with its behavior. We see this problem behavior on both v1.8.5 and v1.8.2, on both iPhone and...
Dear All,
Brief about the requirement:
ToF (Time of Flight) value computed is inclusive of the overhead delay of notifying to the application layer in the BLE stack...
Is it possible to use app_timer with the mesh stack?
Up to now I was not able to integrate the app_timer library into my build.
Can you give me an example how to integrate...
Hello Everyone,
I'd like to know if it is possible to use nfc to collect bonding informations from a smartphone. Then I'd like to transmit these informations to other devices...
Hi, i'm using nRF52 DK to communicate CX93510 encoder chip via SPI. I'm using nrf_drv_spi library with SPI0 connected to pins:
#define CX93510_MISO_PIN 22 #define CX93510_MOSI_PIN...
Hello all, I'm working with construction like:
To pass some data between APP and BOOTLOADER. At first I tried to place this buffer to the end of RAM, but after restart content...
Hey Hi all, I am new to BLE Technology and it's programming. Well, I need some help on my project that I am working on. I have multiple (=25) peripherals and I want each peripheral...
I've got a custom board using the NRF52810 with SDK v15.0.0.
I am using the TWIM driver (nrfx_twim.c master mode) to drive an LCD driver IC, a capacitive touch sensor IC...
hi , endnode, I has changed app_util.h as this link
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104059#104059
the max link...
Hi,
Is it possible to use variable Read/Write twi data length?
I'm using:
nrf_twi_mngr_transfer_t const i2c_write_raw_transfer[1] = { //NRF_TWI_MNGR_WRITE(I2C_HUMIDITY_SENSOR_ADDR...
I'm looking for someone to hire to make a Thingy program for me.
I'd like to program the Thingy so it picks up ANT+ MO2 data or other ANT+ data from multiple sensors and...
