nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have successfully used the guide for BLE DFU.
But now I have trouble using the DFU via serial port. Do you have a guide for serial DFU?
I have tried two things.
...
I have a weird question:
On the nRF DKs (51&52) there are pin headers to connect them to an Arduino.
When delivered, on these headers there are some sort of plastic clamps...
As I working on a new project I am writing the code to support the new SDK driver structure and not including any "legacy" code support.
This highlights the fact that the...
I have a custom board with nrf51422-QFAC, used with SD 130 and SDK 12.3.0. My firmware consist of ble_app_hids_keyboard example modified. Schematics are attached below.
...
Hi all,
I using 1 Provisioner provisioning for some Nodes (light switch server) . If I have 5 Nodes in mesh network
I want to remove Node 4 from network and then add it...
I am working on a BLE peripheral (nRF52832 & SDK 15) which uses the Peer Manager to handle encryption and bonding to a previously existing central device. Sometimes bonding...
I am using the Segger Embeded studio and wondering about the SWO output.
I know I can load code and set break points with just SWDIO and SWDCLK.
So with RTT do I really...
HI all,
I'm working on the nrf52840, and I've tested this on the devkit as well as on-board on the product I'm working on. Using the saadc, if I tie my AIN line to VCC...
My use case initially is a single central sensor server powered from the mians and serving by BLE one battery-powered peripheral that has one of the commonly available st7565...
Hi,
MacOS serial device name is changings all the time when the nrf52 DK Eval board is re-powered. Meanwhile I have /dev/tty.usbmodem49, counting up. Next time I re-power...
We want to be able to download a firmware image into external flash through multiple paths (wireless or wired -only one path is used at a time) then program that image into...
Macbook pro mid-2014
High Sierra 10.13.5
I get the following message when trying to select the PCA10028 on the serial port:
2018-07-06T22:53:49.427Z INFO Application...
Hello all,
Thanks to the wonderfull nrf connect android app, I've been able to setup a BLE peripheral to broadcast the standardised service for "Location and navigation...
I'm digging into OpenThread, using the NRF52840 DK. I find myself spending most of my time trying to figure out module dependencies. Is there any way to quickly get all the...
