Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello, I want to send beacons from one nRF51822 device to another. My project involves using omnidirectional antennas. So, will nRF51822 be the right choice for me?
I was...
SDK 15, nRF52840, PCA10056
When I read my data in the flash I recover the before last value writen and not the last.
I'm using the es_flash.c source code from eddyston...
Hello, I want to acquire my mobile's gps sensor's information using nrf52832 dk. Can anyone please guide me how to do this ? I use keil mdk-arm5 compiler and sdk v15.
Hi
I work for a 7 channels ANT+ receiver. Nordic 52832 SDK12.2.0 S332v2.0.1
The following scenario can been observed and cause high current consumption for a long time...
Hi to all,
i am developing a device that in it i need to measure voltage of battery to report percentage of battery to user, but the voltage that i measure with ADC is different...
Hi,
after migrating from SDK12.2 to SDK14.2 we encountered a problem with GAP Security.
When setting optimization to -Os, the program fails with BLE_GAP_EVT_AUTH_STATUS...
Hi all,
I am trying to use uart-app (segger example in SDK15) to generate hex file, which will be programed to nRF52832 later with Softdevice by nRFGo Studio. ((Instead...
Hi,
we are using the NRF52840 DK and we would like to use our own antenna. We saw on others posts that we have to connect it to the J1 connector's place.
We have some...
Based on the Product Specification v1.0, the antenna load impedance should be 15Ω+j88Ω.
I checked the antenna impedance based on Figure 32.
The simulation result is...
During the development of nrf52832 (SDK14.2), I occasionally get NRF_FAULT_ID_SD_ASSERT error. When the NRF_FAULT_ID_SD_ASSERT error occurs, I can only get the information...
Hi Nordic,
I am working on a BLE based application. In my application, I am forced to use SPI and TWI of same instance.
I am using SPI1 and TWI1. Earlier I was working...
I'm adding key protection to DFU, a batch script is creating the bootloader_config_default.json. I'm using mesh SDK 2.0.1, but started developing using Mesh SDK 2.0.0. When...
Hello everyone,
my question is related to the time interval t TXEN = 140 μs from the radio timing table in the datasheet of the nRF52832-SoC ( http://infocenter.nordicsemi...
Hey Guys,
I am facing problem with building bootloader_secure example. I am using makefile for this purpose.
I am tryng for buttonless dfuimplementation, but the first...
