after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello：
From the nrf52832 data sheet can be seen in the crystal pin is the internal input capacitance, in the table (19.4.2 64 MHz crystal oscillator (HFXO))on P109 , has...
Hi,
I am working with the HID keyboard example in the pca10028 development kit and I facing following problem.
I can connect, pair and bod with Android and IOS devices...
Hi,
I'm testing a PCA10056 S140 (nrF 52840 PDK), SDK15.
I want to test long range extension : using ble_app_att_mtu_throughput application sample.
But when I change...
Hey, I see that the nrf52840 has a single i2s peripheral. and the max sample witdh supported is 24bits. Is there any way to get 4 channel 16bit audio? I only need to record...
Hello Team,
We are using nrf52832 device and SDK version 12.2 Softdevice3.1 to program our watch device.
We have iOS & Android native application to communicate and...
Hi,
I'm trying to transmit data at about 500kbps from custom nRF52 board (peripheral, s132 v5, SDK14.0) to a PCA10040 board with a connectivity FW (based on v3.0.1) connected...
hi to all,
i am developing a device with nrf51822 and i have Inadequate ram problem, i know that softdevice required ram determined in runtime, so there is any way to know...
Hi to all,
i am developing a device with NRF51822 SOC, i want implement a peripheral device and deploy in it a service with two characteristic with notify property, i know...
I want to test the demo https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo that requires Mesh 1.0.1, but I do not seem to find it anywhere. Can someone point me...
Hi, guys! I am working about a project that I need to get data from sensor and send these data through mesh. I referred from link text ,and the example works well. But, I...
I'm looking for a Nordic expert. I have already designed and built a complete PCB based on the Nordic nRF52832, along with the firmware. I need to improve the PCB design,...
On my nRF52 DK, I'm seeing *something* pull down VCC by about 50 mV once every millisecond (1KHz), and I'm trying to identify its source. (This is only important because using...
Our application needs to read 128 bytes from 6 SPI sensors as efficiently as possible. We're currently using a single SPI Manager to read all 128 bytes from all 6 sensors...
Hi all.
Just wondering if i need to go through the tutorials on making a service if i just want to read a few bytes in an advertising beacon.
I'm a little lost on figuring...
