Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
SDK 14.2.
Application Timer Library
I had a question regarding the Application Timer library and the way it checks for timeout handlers. In the documentation, it says...
Hi, I have problem with nRF51822. I've bought cheap China miniboard with this chip. I can program some examples (precompiled HEXes) with J-LINK and they works correct, but...
Hi,
I want to make a program in order to assing functions to the buttons and manipulate movile phone apps without making any app or configuration into the phone.
What...
Hello,
I've a process, let's call it P1, that sends I2C instructions for a LED driver (it's like an infinite loop of I2C instructions for registers management that have...
Hi all,
I want to make touch button by my NRF52832 board . I am trying Csense_drv example but The value of change is constant when I log on UART . LED flashes continuously...
Hi Team,
I am working with Nrf24L01 chip with ATMEGA328(ATMEL C code) i made separate TX and RX module it works fine. But i want TX and RX in same module i done coding but...
Hi.
I am using SDK15 and want to control keyboard and mouse using HID with nRF52840.
I used the HID example to verify that the keyboard and mouse work when the button...
Tools in use, etc:
nRF5_SDK_for_Thread_and_Zigbee_v1.0.0
RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha
NCP example located in <InstallFolder>/examples/thread/ncp/uart...
I use nrf52832 qfaa b017351o ,some ic can run sdk11 dfu demo but some ic can't. Demo location .\nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132...
Hello,
We have a custom board based on nRF52832, built an application base on SDK V15/ble_app_uart
It works fine with Android: we can send string over BLE but it doen...
Hi everyone,
I changed the example ble_app_beacon from sdk 15.0.0 sd132 to be able to scan beacon besides transmit. It works well to scan beacons and I can get their UUID...
I am using SDK15 and S140 and nRF52840 as central. I plan on deploying a lot of temperature sensors each of which will
have a nRF52840 acting as a peripheral also using...
Hello Community,
I am looking for a code example of the DFU part application of the nrfutil library in C.
Please someone can give me a fair example of the function
def...
Hi,
we would like to add a level of encryption above BLE. So first establish a secure connection via BLE and then exchanging message to establish a session with a second...
