I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi all,
I'm trying to enable Bluetooth 5 extended advertisement in nRF52840.
Currently, I'm using Nordic SDK v15.0.0 and S140 Softdevice v6.0.0.
In order to init the...
Dear Nordic Support Team,
I want to send the new PCB layout for manufacturer but I am not sure that
I can use any pairs of pin for DFU over serial or not.
I want to...
Hi all,
I have a question regarding the BLE mesh specification. When you are transmitting data using advertising frames, how does it check if the transmission medium is...
Hello everyone,
I am working on DFU bootloader application for android and iOS (using Qt C++).
For android everything works fine, but for iOS I have problems.
In order...
for the mass production what is the best solution in order to flash the nRF52?
for the mass production can I use DK PCA10040 ?
The DK PCA10040 can be used for dubbug on...
Hi I'm using Keil MDK 4.7 with nRF5 SDK V15, both of the 2 SDKs are installed at C:\, and the Keil4 Nordic License has been installed. When I tried to compile one of the example...
Hi all,
Is there any possibility to intimate any documentation errors(spell mistakes, content doubts, etc) to nordic documentation team?
Thanks,
Sridhar
Hi,
I have used examples\dfu\secure_bootloader\pca10056_ble application and successfully updated two applications(heart rate and health thermometer) over BLE. In order to...
Hello, i' trying to measure the power consumption of the nrf52840 PDK. So far i have been able to measure the current. How can i go about measuring the voltage and is it constant...
Hello, I recently received a Thingy:52 and was able to connect to PC using J-Link. After uploading Heart Rate Monitor program Thingy is no longer able to be added using iOS...
Hi,
I am facing difficulties porting Mesh examples to IAR.
I am getting the following error : #error "Your compiler is currently not supported." during compilation from...
I'm working with nrf52 dk to read the sensor dht22. i need to follow this steps to make sure the sensor is ready to send data.
Wait until DHT responds and pulls the line...
The problem is that the load was made via application, using nRF Tools in the DFU option, since I wanted to understand what I did with the files and others, but now that I...
Hi,
In nRF51822 proprietary ESB protocol. there have define a "noack" field in structure "nrf_esb_payload_t".
Normally, the "noack" field is set to "false" in transmit...
Hi,
Now,I made a NRF52832 scanner gateway with SDK15.0 and softdevice 6.0.0.
I want it to scan advertiments continuly. So i set SCAN_WINDOW and SCAN_INTERVAL (they are...
