Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I reference demo1 of PWM driver example in SDK15.2.0, I make myself PWM driver. the official demo1 use pin17-20 as PWM channal1-channel4, but I use Pin9-P12, I modify the...
Hello,
I would like to measure the frequency of a signal and I use PPI, a timer and input capture to achieve this. Here's the configuration :
The frequency of my signal...
Good evening,
I am using NRF52840 board with softdevice S140 and SDK version NRF5_15.2. I am currently trying to compile the ble_app_hrs_rscs_relay example on SEGGER studio...
Hi ! I have attached the PCB design and schematic provided by Nordic for nrf52832 which is said that its also same for nrf52810.
I wanted to use the nrf52810 board for beacon...
Hi all, i'm Duy
I'm doing my thesis project about Bluetooth mesh. My board is nrf52832 custom board which is similar to pca10040. i want to build a mesh network with several...
Hello, I'm able get an updated battery service value on nrf connect using the 15.2 s112 proximity example on the DK using a cr2032. Then adjusted the clock to LF RC and removed...
Hi,
Let's say I have a door lock module without user interface... no keys nor display but with bluetooth peripheral module. The user pays is room via the application then...
Hello,
I would like to know if it's possible to simply configure all parameters for a BLE connection by a PC software.
The goal is to manage the BLE parameters to measure...
Hi,
I want to create 1 hex file that will contain my bootloader, app and softdevice.
I know i can use NRF GO studio in order to read each hex individualy but it is of...
Hello,
I am using PCA10040 development board based on nRF52832, Softdevice 6.1.0 & SDK 15.1.0.
On the Nordic website, I have verified that Softdevice v6.1.0 supports Chained...
What is the best practice for protecting against ESD for unused pins, should I leave them floating or ground them? I noticed in other posts here that it has been recommend...
Hi!
I use HID example and try to understand in a hid service init for why report_map_data[] with a table.
What is do this array? If I use keyboard example, I should get...
Dear Sir,
I am working on nrf52832.softdevice S132. SDK15.
I am getting the following messages when I try to connect to the peripheral using nRFConnect.
The error is...
