Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Dear Sir,
I am trying to use a whitelist on peripheral side so as to connect the peripheral to a given phone/App.
At first I enabled the "p_advertising->adv_params.scan_req_notification...
I am requesting a USB booloader hex file or if possible the complete project. I have been doing some hacks on mine and have erased the USB booloader. A quick search through...
We are working on the BLE Smart Switch. The requirements are pretty generic:
Low Power consumption
To be used by multiple smartphones within the house
The obvious...
Hi,
I want to set the TX power in a mesh proxy configuration. I have read mesh sdk2.1.1 TX power of nrf52832 , which works good for not proxy situation (e.g for light_switch_client...
Hi, I'm having troubles adding PWM in light_switch_proxy_server example in Mesh SDK v. 2.1.1.
It seems that the PWM driver and instances are not correctly enabled, looking...
Hello,
I was wondering if there are any article or tutorial I can follow to optimize code build with Segger Embedded Studio.
I was able to follow this article( https...
I need logging in almost anything I do, but I've never been able to start from an example that does not use logging and add logging. I've set the NRF_LOG_ENABLED and NRF_LOG_BACKEND_SERIAL_USES_UART...
Hi,
I am using nRF5 SDK 12.1.0.
I have read the s132_nrf52_3.0.0_migration-document.pdf and I am trying to implement the whitelist without the private addresses i.e...
Hello Everyone need your help.
I am using three nRF52840 dongles and have flashed hex file of an nRF example (Ble_Blinky). i want to know whether the hex file is really...
Hi, I am using SDK 15.0.0 and FreeRTOS 8.2.1 (from SDK 14.2.0).
I consistently get a stack overflow on the Idle task, caused by PendSVHandler in port.c
This can be easily...
Hi,
I'm using nRF52832 on nRF52 SDK v15.0 with S132v6.0. I know that 52832 support high throughput and advertising extension. We have more than 31 bytes data to put in the...
Hi,
I have created up to 5 custom services with several characteristics (4 at maximum) each one. They all use the same base UUID.
The problem I'm facing now is that when...
I am adding CLI service with my existing project developed based on ble_app_uart.
CLI Init function :
static void _cli_init(void) { ret_code_t ret;
#if CLI_OVER_UART...
Hi,
to be able to send more advertising data, i want to cyclical switch between different advertising packages. This already works so far.
Do i need to include the AD...
Hi there,
I am assessing the possibility of replacing a low-power MCU in one of our products with an nRF device.
Currently, our low-power MCU spends most of its time in...
