Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
I was using for some time my code with FTDI USB converter to UART.
Recently I got built new boards, all with IC top marking N52832 QFABB0 1717AQ
and whilst any other board...
I would like to use PPI in order to set out pin and start a timer at the same time, from software.
I cant find a way to create an event from software that will fork a START...
Hello everyone, I'm currently writing my bachelor Thesis and need to establish an iot (preferably mqtt) connection from my pca10028 with my PC as broker (i.e. with mosquitto...
Why is AAR blocked if the Peer Manager Library (e.g. SDK12.3 see id_manager.c) uses the -softdevice SoC API- function call sd_ecb_block_encrypt() to resolve RPAs (Resolvable...
I am trying to connect to 8 slaves/peripheral with a single central/master connection but i wan to understand that how the connection us managed between the multiple slaves...
Hi;
I using experimental_ble_app_buttonless_dfu as the project. After build the project and download with softwareDevice , it works ok . Then I compile bootloader_secure...
Hi
I have done setup using guide ( https://github.com/sandeepmistry/arduino-nRF5 ) by sandeepmistery.
I am able to blink led of nrf52DK using Arduino example code. ...
When i choosing among the 52832 and 52840, i found this table.
One point i am not sure, i believe the 52832 stack is already support Bluetooth 5, but why the table said...
Hello,
I would like to manage time (hours, minutes, seconds) on NRF52 chip: what is the best way to do it ? How to use as less energy as possible ?
At the first connection...
Hi all,
I'm new to Bluetooth technology and just start some test for indoor localization using 52382. But I find out that 52382 does not support the long range feature of...
Hello all,
I'm curious if anyone could lend some thoughts.
I'm just in the research stage and going through a few examples but getting a little overwhelmed.
I'm trying...
Hi,
I am using nRF51822, S130, SDK 12.3.0
Want to use is low power failure warning. using the following code.
However, when break on line err_code = sd_power_pof_enable...
I am currently using a CSR 4.0 dongle 8510 A10 chip on Windows 10 Creators update
I can get it to Pair with the nRF52832 in windows, according to windows.
I have a ...
