I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
How many crystals/oscillators do I needfor a NRF51822 WLSCP chip?
I looked at datasheet and I'm assuming I will need a 16 Mhz crystal, a 32Mhz crystal, a 16 Mhz oscillator...
I am using IAR workbench and working with the nrf52 DK, using the S132 v.3.0 softdevice. I used the blinky example code to connect the nrf52 with my android phone over BLE...
Hello,
I got TCP Server example working on nRF52DK with Raspberry Pi.
I set everything up and can ping global addresses of DK on all interfaces (wlan0, eth0 and bt0) from...
Hello,
I am using NRF52832, SDK v15.1.0.
For advertising on single channel, I added " p_advertising->adv_params.channel_mask[4] = 03; " in ble_advertising_start() ,...
SEGGER Embedded Studio 3.12
nRF52 SDK 15.0.0
In order to generate peripheral driver library files，how to create library in project(have .c&.h file in this project).Only...
Hi,
SDK documentation says "You cannot write to UICR.BOOTLOADERADDR when using the default J-Link target driver in IAR". Some threads suggested it is only nRF51 issue, but...
Hi!!
Now I am using sdk 14.0.0 / example / peripheral / spi / pca 10040 / blank / arm5_no_packs /
I am sending commands to ads 1192 with nRF 52832 DK as master and after...
I had an issue on using HID to control the media in Android. It worked fine at the first connection, I could play , pause and change the song on phone. But it couldn't control...
Hi I would like to confirm which NRF51822 models are the 0.35mm thin WLSCP package. I checked Avnet distributor and they say that NRF51822-CTAC-R7 is 0.35mm but the package...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
I need to make an android custom app (with UART functionality) so that only...
I'm trying to get a third party demo application working and I seem to be having an issue with the nrfx_spi_xfer function getting stuck waiting for the NRF_SPI_EVENT_READY...
Hi everyone,
I'm learning about proggram the nRF52840 dongle and I tried to code an interruption. Press the SW2 to turn on a LED
So, looking at this code, where did...
I am trying to make the nRF24LE1 as a sensor node. So I want to configure it to work as a receiver/transmitter and simultaneously use the ADC and UART. But the moment I added...
Hi all,
I'm using nrf51822 and ble_app_multirole_lesc example on SDK 12.3.
When I connect with "nrf connect" Android application for the first time, the bind is established...
Greetings. Finally ordered some NRF52832 board from HOLY IOT and spend few weeks trying to handle with them.
So, all about setup:
SDK: 15 (15.0.0_a53641a) @ Windows 7...
