Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Errors while starting debugging session
I am getting error 65 'access violation' in Keil Uv5 and 4.
In IAR , I am getting 'User Error:Stack Pointer is setup into incorrect...
Hi,
I modiy the usbd_hid_generic example to tow endpoint by sdk15.0.When i use the USB testtool send some datas to usb deivce,the d atas cannot be read properly by NRF_USBD_EP_OK...
Hi, in our one project we are using nrf52832 radio to transmit the data packets. After transmitting the data packets, the nRF52832 chip need to disable the radio to minimize...
Using SDK 15.0.0, I have ported the peripheral/usbd example to custom hardware based on the nRF52840-QIAAC0.
In the nrf_drv_usbd_enable() function, execution hangs at
...
I'm communicating with a temperature sensor using I2C/TWI and I'm now trying to send that received data over BLE using the HTS service.
When I send a ble_hts_meas_t with...
Hello,
I am using nRF52 with ADS1292, and i am trying to sample at 8kHz with data throughput of 72kB/s, but some data is being randomly shifted giving me random spikes...
Hi Nordic Team,
I am requesting any block diagram level documentations - on a high level software architecture overview of SDK.
My goal is to understand how different...
Hello All,
I want to know Maximum External flash size supported by nrf52832 .
On which parameter Maximum size of external flash depends?
If it depends on usage, then...
Hello,
I'm currently using a bootloader based on the one included with SDK 15. We're close to mass production and I need to decide on how much space I should leave for the...
Hi,
I have designed a system that uses the SAADC to sample 3 analog inputs in scan mode at 8 KSPS, performs downsampling by a factor of 8 using the DSP, and sends the results...
Hello community and Nordic support.
Very briefly about my profile: I have worked with NRF52 chips in my previous company for about half a year and have a good understanding...
in my tutorial I need to implement an I2C or TWI sensor on a peripheral BLE. In SoftDevice Software in Example-> Peripheral there are 2 methods 1) twi_sensor or 2) twi_master_with_twis_slave...
I used nRF Mesh app both iOS and Android versions to communicate with
nrf5_SDK_for_Mesh_v2.0.1_src\examples\light_switch\client
and
nrf5_SDK_for_Mesh_v2.0.1_src\examples...
The system consist of two nRF52832, one acting as SPIM and the other one as SPIS. I hace created a while loop always asking for certain amount of bytes but the MISO line on...
Hello, I am new to nRF micro-controllers and using Netbeans. I have cloned the repo of a project I would like to run, which builds successfully, and am getting the following...
