Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
I'm working on sending string data over mesh by following this case , my message is printed on server side in mesh_msg_handle() function (access.c file), but I want...
Hello guys I'm using windows (10) using parallels in a virtual machine in mac (high sierra), all in its latest version.
The board is a PCA10040 V1.1.0. with the bootloader...
I program SD132 into nrf52832 and then program bootloader secure into nrf52832. on nRFToolbox is show name " DFUTARG" I'm using nRFToolbox for OTA. When OTA process is successful...
Hellou, I am developing apllication mesh application from example light switch. In application program i receive data from mesh and this data is stored to external serial...
I am looking for the third party nrf 52832 BLE module in which i need following configurations,
Size is less then 9mm*9mm
Chip antenna or PCB antenna
GPIO pins atleast...
Hi!
I would like to completely isolate the nRF52840 on the Preview-DK (2017.32) on hardware level.
Scenario
I would like to power the nRF IC with the external supply...
Hello, I'm new to Nordic boards.I would like to measure the bit error rate for a BLE link using nRF52840.
Is there any way of modifying any of the existing examples to add...
We use iOS nRF Connect primarily for DFU updates and find a real annoying issue with its behavior. We see this problem behavior on both v1.8.5 and v1.8.2, on both iPhone and...
Dear All,
Brief about the requirement:
ToF (Time of Flight) value computed is inclusive of the overhead delay of notifying to the application layer in the BLE stack...
Is it possible to use app_timer with the mesh stack?
Up to now I was not able to integrate the app_timer library into my build.
Can you give me an example how to integrate...
Hello Everyone,
I'd like to know if it is possible to use nfc to collect bonding informations from a smartphone. Then I'd like to transmit these informations to other devices...
Hi, i'm using nRF52 DK to communicate CX93510 encoder chip via SPI. I'm using nrf_drv_spi library with SPI0 connected to pins:
#define CX93510_MISO_PIN 22 #define CX93510_MOSI_PIN...
Hello all, I'm working with construction like:
To pass some data between APP and BOOTLOADER. At first I tried to place this buffer to the end of RAM, but after restart content...
Hey Hi all, I am new to BLE Technology and it's programming. Well, I need some help on my project that I am working on. I have multiple (=25) peripherals and I want each peripheral...
