Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
hi to all,
i am developing a ble device with nrf51822 and i encounter with a problem, in my program i have code like below :
in this point program work well, but when...
Hi
I'm facing a problem with light switch demo from mesh SDK v1.0.1, when running the light switch client, as shown in the rtt viewer below the configuration of the server...
My customer is modifying the code based on the example provided in the SDK 15.0.0 to suit their project:
Project file from the SDK under \ nRF5_SDK_15.0.0_a53641a\examples...
Hi,
I am making a project with the nRF52832.
In this project i must configurate another chip with SPI.
The timing must be very accurate. Now the problem is that the...
Hi Team,
I am using nRF52832 to implement smart watch product and it is now close to PP stage.
Currently our product testing engineer found that in a relative noisy environment...
HI. I used a translator.
I want to control the mouse and keyboard using HID with the nRF52840 PDK.
I found the HID example in SDK15 and compiled it
The Infocenter...
Hello,
The sd_softdevice_enable never returns, how can I investigate please ?
With my Jlink probe, it's look halted at address 0x000008CC.
Configuration:
SDK 15...
I''m trying to run a piece of PERIPHERAL example code running on a nrf51422 devboard
I'm using sdk 8.0 and the example's relative path is:
>nRF51_SDK_8.1.0_b6ed55f\examples...
Hi, We have a BMD300 nRF52832 acting as a BLE peripheral connecting to up to 8 phones acting as BLE central devices. We started noticing that we are getting BLE_GAP_EVT_DISCONNECTED...
Hi,
Just a small question. In the SDK 15 documentation for the Experimental: GATT Module documentation, could it be that the following sentence "The default value that the...
I can't work arround error 133 on Samsung S7. After several test I found that it's related to long advertising intervals. I've test it on nRF52 DK and nRF51DK. I've test it...
Hi, I'm migraing our project to the latest NRF5 SDK v15.0.0 (S132 v6.0.0). We were previously on v12.2.0 (S132 v3.0.0) using the BLE DFU Bootloader. I've modified our bootloader...
Hello.
I try to modify ligh_switch_demo to switch state of 4 servers. I prepared 4 custom boards (server), one client and one provisioner. Provisioning was successful. I...
