Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi to all,
i am developing a device with nrf51822 soc and i want use it as peripheral, in it have a characteristic that i want read it continuously from central. sometime...
I am using Hackable kit which is a custom nrf52832 board with Bumpy a low cost Black Magic Probe alternative to program since i don't have a J-Link device. I have tried many...
Actually, I am working on a IoT project in which tens of connectionless BLE beacons are broadcasting packets. Now, four Nordic devices(nRF52832) are receiving that data and...
I want to use the 2450AT42E010B chip antenna from Johanson Technology in my design. I selected this antenna specifically because i want to make a beacon using the nRF52832...
I want to build a device able to connect with smartphones and central modules preinstalled on the ecosystem.
Is possible to integrate Bluetooth mesh + Peripheral role in...
I have the nrf51 RADIO peripheral set up with the usual set of shortcuts:
NRF_RADIO->SHORTS = RADIO_SHORTS_READY_START_Msk | RADIO_SHORTS_END_DISABLE_Msk | RADIO_SHORTS_DISABLED_RXEN_Msk;...
Hi,
I'd like to be able to use an event from the LPCOMP to sample the RTC (either to a peripheral's register, or to a memory address), so I can measure pulse widths without...
I am able to initialize the module and get the callback , but when I try to write I will not get the callback after the write, and no errors.
If I simply try to read after...
Hi
I am integrating BLE with LESC into a legacy sensor product using SDK v11.
The problem I am running into are errors in the FDS module when trying to make a secure connection...
I use nrf52832 based on SDK14.2 as a slave development. Occasionally there will be a crash in the operation. The program has been running in the “params_reply_pending_process...
Hi Nordic Community
I'm doing a risk assessment, and I couldn't find a proper answer for the fallowing two question, it would be great if I could have your opinion and...
I am trying to set up the sniffer on nRF52832 DK PCA10040. I am not seeing the COM port on the Wireshark interface. I can see it on the device manager. I have looked at other...
Hi Everyone , I am using SDK v15.0 for nrf52840 with segger embedded studio.
I tried the example code given for blink freertos. I am able to run two tasks but as soon as...
Hello,
I am using nRF52832 and having a problem with the Low Power Mode. I am not sure if I am either not getting it to stay in low power mode when my UART is initialized...
