I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I want to design NRF52832 with 2.5 VDD and connect to an UART IC (CP2012),
unfortunately, "CP2012" just work in minimal 3.0V.
So, here is the question,
When NRF52832...
Hi,
I have recently tested some commands from the radio test example given in the following link using a PredevKit for the nRF52840 and it was quite fine:
http://infocenter...
Hi.
I'm struggling with BLE example projects on the my custom board.
my board uses nRF52832-QFAA, 16MHz external crystal with no 32,768kHz optional RTC.
and I choose...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
There is a shift to SDK 15.0 as a measure against "nWP - 031", but can not cope with nRF...
i have SDK of mesh version 2.2.0 and nrf5 SDK version 15.1 My question is what are the steps I should follow after flashing the hex file into the dongle. I am using nrf connect...
I am having some difficulty reading the NRF_GPIO->IN. Specifically I have set up one event function for three different input pins, the phase of a motor. The event is on toggle...
Hi Team,
Got a high current issue with uart from customer.
When the nrf_serial_init() is called and the uart is configured as dma mode(used as UARTE), the average current...
Cheers, again!
Our project uses an array of different modules, many of which will need to make use of the TWI manager. I've been able to create the manager successfully...
I'm working on a custom BLE keyboard (starting from the ble_app_hids_keyboard example, S132, seeedstudio nRF52840-mdk board, SDK v15.1.0).
The system is configured to wake...
I am developing on RAYTAC MDBT50Q-DB board.(nrf52840)
I measured current comsumption on RX mode.
with DCDC: about 8mA
without DCDC: about 11mA
datasheet written...
I am working on a LIN slave.
I have working code on an Atmel 2560, just porting it to the NRF52 now. The complication I am foreseeing is that on the Atmel part I could...
i'm using the sdk only for ble serial data transfer, which i'm not using for this pwm test
all code talks directly to the hw registers
those are some code snippets to...
Hi, There are some older comments. Since situation is changing fast and I am un-sure if these comments are out-dated or not.
ROM size. Some comments said 51 is small...
I'm using nRF connect 2.5 on PC and the latest Android app on a Pixel phone. My firmware is based on SDK 15.1 and soft device 6.1.0. I am using nRF52840-DK boards.
My firmware...
