Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
Hi all
The errata sheet V1.8 states that the errata 143 applies also for the Bluetooth Low Energy mode. Does that mean that the BLE stack of the SoftDevice S132 is also...
Hi,
I am using nRF52832 DK and other same custom board, sdk v15.0 with SES IDE. My application like this:
For ble peripheral used example ble_app_uart and for central...
Hi Sir,
In my system (windows 7), I had install the GCC 4 .9 2015 q3 for SDK 14.2.0/12.3.0.
As reference the release note of SDK 15, the GCC upgrade to 6-2017-q2-update...
Good Morning Team, Hope your day is going well! Can you please provide the Full Material Disclosure (FMD) document for below part since I could not locate it on website. ...
Hi, I am merging the multilink example and the CDC ACM example in SDK15.
However, if you merge and run it, it will continue to fail.
Here is the source.
I have...
Hi, i am using a model based on simple_on_off model to send custom messages.
For now provisioner and client are separated as in the V2.0.1. I tried to combine them first...
Hi,
Is it OK to use the Nordic Semiconductor ASA (0x0059) ID for broadcasting data in the manufacturer specific data field?
If so is does Nordic provide a specification...
Hello
For the BLE Mesh 2.0.1 demo i bought some nrf52840 develboards. Then i write the demo with "python scripts/quick_start/quick_start_demo.py" to the nrf52840 develboard...
Dear Nordic Team, Thanks for supporting.
I want to know the possible for mesh network concept with nRF52832 (PCA10040). If possible means guide me for startup.
Regards...
HI!
I'm a happy owner of two nRF52840 Preview DK board (v0.9.3). I'm considering to change their chips to production versions. I found that schematics and PCB layouts are...
Hi,
We are using nRF52832 for one of our central device. Our peripheral is also based on nRF52. We are facing issues while scanning for the peripheral from the central side...
