At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
HI:
Always error while porting,Error: L6218E: Undefined symbol app_uart_init (referred from main.o).
I added a path, and ENABLE UART_ENABLE 1 in sdk_cofig.h
Compile...
I have set up the gcc toolchain on Mac OSX to compile my BLE nRF51822 code and I tried to flash the code. Here are the 3 scenarios that I have tried (JlinkExe on Mac)
Case...
Hi,
I am not sure if this is the right place to open up a thread about a zephyr HCI firmware issue. Since Nordic also contributes to zephyr I'm putting up this question...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi All:
When I simulated PWM by GPIO, the output current noise was shown like the picture below (red circle area):
Cause it will lead to a loading issue in the backend...
I want to implement a long write. The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi Nordic team,
I have 2 nRF52840 DK boards.
I followed the steps mentioned in the below link, I am able to Transfer the DFU archive over serial with nrfutil(LED keeps...
I want to enable the Logger Module to have the high default severity of Error and then be able to enable lower level severities on an individual module for debugging. Is this...
Hardware used: 2 nRF52480 DK boards
I am running nRF5_SDK_15.0.0_a53641a\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput example, I want to increase...
I read zephyr official document of nrf52810 support：
http://docs.zephyrproject.org/boards/arm/nrf52810_pca10040/doc/nrf52810_pca10040.html
It describes like this : ...
Hello,
I just got my nRF52832 DK and am following the Getting Started at the Infocenter to get familiar with it. Running Ubuntu 16.04 and all the latest Nordic tools (SDK...
Greetings, I got a nRF52832 DK and only just found out that Smart Remote 3 is probably more what I'm looking for. It should be no problem to set it up on the DK with an appropriate...
I am working on a custom board based on nrf52810 that my client provided. In this board the accelerometer (Bosch BMA250E) power has been controlled by the PIN 9. However when...
Hi, everyone
I have some problems to make the Image Transfer Demo APP work
I have read the content of the website( https://github.com/NordicPlayground/nrf52-ble-image...
