Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I would like to know if I can run Thread examples on nRF52840 USB dongle? Could someone provide instruction how to do this in a Windows environment?
Also, is there external...
Hello,
I'm trying to lower the power consumption in the s.c. "System ON" mode. I need to run in System ON mode to keep the RTC running. However I need to wake the CPU on...
hi ,
I use SR3 V1.2 to test. I enable ANR, play the recording directly in the loop.
About every five seconds, a second or so of unusual sound appears. The rest of the...
Hi,
I can't understand what is DFU example inside /examples/dfu folder and what is /bin/bootloader/? I read DFU quick start guide, but where is source code of bootloader...
I try debug my app in keil debugger but it's often raised app: SOFTDEVICE: ASSERTION FAILED in SEGGER after step down through the code (in few steps).
My app based on buttonless_dfu...
Hi,
I have a doubt regarding buffer setting in SPIS.
In the SDK15 SPIS example, buffers are set using nrfx_spis_buffers_set(...) and it works perfectly.
I was wondering...
Hi All,
I am using nrf mesh SDK v2.2.0 and nrf SDK v15.0.0.
I have created a new model in nrf mesh SDK, this model is publishing scanned data on group address.
When...
Hi,
I was working on the HID mouse example and noticed that the example gets disconnected from my mobile phone once i start moving the cursor.
I also noticed that the...
Hello,
I am performing current measurements on custom hardware with the nRF52840 and comparing my results with the values in the nRF52840 product specification. I noticed...
I have downloaded nrf5_SDK_for_Mesh_v2.1.1_src and tryign to build the client and server example to test the Lighting Mesh example from the Android/iOS apps available on the...
Dear Nordic Team
I have changed pwm driver example as you see in bellow . i also observed the codes which you linked for pwm. Bellow code works without the effect of update_pwm...
We are trying the HID Keyboard example using SDK 12 with no modifications on the nRF52 (PCA10040) board. We are able to pair and connect on both iOS and Android the first...
Hi,
I have a nrf52 DK. I currently tested apps on run smartphone. Similar to nrfconnect, toolbox, uart.
Laptops also have bluetooth. Can i use laptop's bluetooth to communicate...
Hi, I would like to create a new target,but nRF52810 only can be compiled with makefile and I don't know makefile too much.
I try to edit the makefile with my own target...
Hi guys,
I'm using following setup NRF51822, SD130, SDK 12.3.0. I control one transistor with PWM output via timer 1. Before enabling PWM I start 8bit ADC task to measure...
