Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Segger Embedded Studi, SDK 15.2, Windows 10
Nordic NRF52DK PCA 10040 1. 2 .4
Hello again everyone, I have gotten farther with my previous issues of not being able to access...
Hi All,
I am new to embedded low power design and would love some tips on power saving steps and tutorials for the nrf52832 device.
I am trying to understand the power...
Hi,
for a project I need to perform a DFU Update over BLE. After I prepared the bootloader (generating public and private keys and building it), I prepared the update packet...
Hi, I develop device for custom location service based on BLE. Now I'm working with nRF52 Development kit v1.1.0, nRF52832, SDK v15.0.0.
I have a problem with adding 16bit...
Hi,
I wonder if all Tracedata[n] pins are needed for debug? That would make five IO:s useless for other functions. Or is it possible to use 1-bit mode or something similar...
I wnat to set P0.30 and P0.31 for I2C CLK and SDA. nrf_drv_gpiote_out_config_t out_config = GPIOTE_CONFIG_OUT_SIMPLE(false); err_code = nrf_drv_gpiote_out_init(30, &out_config1...
I set up my nrf52 self board with internal LDO using reference schematics with internal LDO setup.
Im entering the power safe mode using __WFE instruction
Also i did...
1.I used Timer2 Capture function Time Frequency is 1MHz. Picture1 Current counter should be 33330. Picture2 Current counter should be 5000. Picture3 Current counter should...
Hello,
I am having an issue with setting up the event generation timing on the nRF51822. Long story short, I am configuring Timer/Counter 0 to generate an event every 50ms...
Hello,
I am using NRF51 DK for developing an application. I tried running the default SPI example in the SDK 12.3 which uses the spi and spis example. The location of those...
Issue exists in SDK 15.0 and probably many many others...
I noticed that the nrf_log_push parameter is indicating it must be a constant pointer to a mutable character...
I'm attempting to pull the mesh bootloader out of the sdk and put it in its own makefile project, so it can be built separately.
I'm building with `gcc-arm-none-eabi-7-2017...
Hello,
I want to achieve bidirectional data communication between one central and two peripherals. Any my central device should be able to do bi-directional communication...
Hi. I have been looking through the forum to find anything that could answer my problem, but can't seem to find it. I am working a project, where our needs is to use a nrf52...
