Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Using a nRF51802, but can't find data about actual reset level other than min. VDD 1,8V ?? (Page 34 in datasheet )
I need to know actual reset level (VDD) for both rising...
Hi to all,
i am developing a device with NRF52840 DK, in my device i had implemented a service that has some characteristic with noti/read properties. notifications work...
Hi when I try create an account on www.nrfcloud.com on a desktop using Microsoft explorer it doesn't move forward and states "fetch" not defined. Any thoughts?
nRF Toolbox scanner code does not seem to discover devices which advertise a 128-bit service UUID.
I have extended the Template app (within nRF Toolbox) to interact with...
Hi to all,
i am developing a device with nrf52840 soc and i want connect to Windows 10 though ble connection. in my device i had implemented an HID service that should act...
Hey is it possible to use advertising beacons together with an server or there will be some collisions in message reception ?
what i want to do is: setup a mesh which consist...
Is there some guide to help implement UART using nRF Toolbox source code for ios?
I am trying to figure out how to use:
Scan, connect, pair and UART
Any help apprec...
when performing db discovering using a peripheral nrf52832 (running sample dfu project) from sdk 13 from a nrf32832 central on sdk 14 I notice that the db discovery event...
Hi Sir
I would want to download code to Ublox NINA-B301 by command line, but it looks not working, please help.
nrfjprog.exe -i 483064601
nrfjprog.exe --family NRF52...
Hi,
I'm trying to perform a DFU firmware update via command line using nrfutil dfu ble.
The same update using nRF connect works fine. The dongle is flashed with connectivity_1...
I would like to have a ZigBee stack running on the 52840 and use door/window (contact) sensors as well as motion (PIR) that are available on the market today to connect to...
Dear Sirs!
I use compiler IAR 7.80 with Nordic SDK 12.2
Softdevice
s132_nrf52_3.0.0_softdevice.hex
I have very strange issue in debugger.
Break point works, but...
Hi folks,
I try change blinky code for nRF52810 SoC. I must create own timer. I dont know app_timer example help for me?! I want to do when power on leds on 2 seconds...
Hi All,
I am developing an application in which i am interfacing the nRF52832 with an ADC via SPI.
I am doing channel multiplexing (2 channels) such that when i get data...
I'm aware of the limitations on using "printf" in a non-debug environment, but apparently there must be something similar with sprintf. I'm using it to load a value into a...
