Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
Hi everyone,
I have an nRF52840 DK. So far, I have been programming the nRF DK using the UBS connector J2 and everything worked great.
Since yesterday, by following the...
I want to update status in manufacturer specific data of advertisement packet. is there necessary to stop advertising first then reinitialize advertisement data and again...
Hello peeps,
nRF52480 I2C Interface with Invensense ICM 20948. I am using SDK 15.2. I see there is some Support for MPU 6050 Invensense but not for ICM 20948. A lot of Registers...
Hello,
I am currently working on the nRF SDK for Mesh v3.1 and I am using a static provisioner as in the light switch example. I have merged the client and server functionality...
Hello! I have a custom board with a NRF52832 chip that is working fine with the last program I flashed into. But since yesterday I can’t access it to load a new code (flash...
What all do I need to modify in the Blinky peripheral (from SDK 16) with in order for the 840 DK to advertise and connect with CODED PHY in long range mode?
My code compiles...
Hi everyone,
I am looking at using MQTT v3.1.1 with TLS 1.2, to send data to Azure IoT Hub.
I tested the MQTT Simple sample and it worked perfeclty. So I am modifying...
nrf52832 , I have flashed ble_peripheral/ble_app_uart with simple modifications
ble doesn’t advertise while Jlink/seggar debugger is connected to our custom board.
...
I use SDK16.0
use BLE + Multiple Beacon, Beacon use timeslot,BLE use softdevice.
I want to modify the advertising content of BLE,But use advertising_stop->advertising_init...
I'm currently working on integrating modem FOTA updates into my application. I have the FOTA working at the moment, I'm able to go to and from a FOTA-TEST version with the...
I try to run this sample https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/mqtt_simple from the master branch, but when I connect to the network...
I'm connecting the battery to the VDDH 3.6V or 3.7V and sensor to VDD, it means nrf52833 get powred on from VDDH and sensor get the power from VDD. is it ok? please check...
I use the nRF52840 MCU and SDK 16 with S140 softdevice. I want to use spi interface to control 3 SPI slave. They share the same SCK, MISO and MOSI. I use 3 chip select pis...
