after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
In my application after some timeout i am trying to stop BLE advertisement.
for this i am checking current connection state,If it is connected or disconnected.
if...
I'm using the TWI_MNGR to schedule a transfer. I have copied the nrf_twi_mngr_perform() function to a function called nrf_twi_mngr_schedule() which does everything except...
Hi team,
I am working with the nRF5340 PDK v0.8.0 and I am trying to request the additional voltage for the VREGRADIO to support the additional 3 dB TX power on the RADIO...
i have a project with Nrf24, i'm using NRF24L01 + PA LNA 2.4Ghz with athena, to get 1000m -2000m range.
But i saw on nordic website that nrf24 not for new design, we have...
I have seen a few references to SoftDevice in the 6.x series not being able to transmit at 500kbps in these forums, but I can't find anything in the docs to reference. Can...
Hi, I am using nrf52832 dev-kit. I use P0.23 or P0.24 as an input pin. I am trying use this pin to read data from other device. When I use this pin like button, it can detect...
Hello,
I would like to get some input on general framework options for development.
I am starting by strictly following the SDK framework, trying to use its drivers, translations...
Hi,
Sorry for putting so many questions in to single thread :)
----
I am looking for information on what all images been integrated to zephyr/merged.hex, can you point...
Hello!
I'm currently implementing Modbus RTU into my nRF52832 to enable the CPU to communicate with other Modbus RTU capable devices.
When communicating via Modbus...
Hi, I am relatively new with ble and nordic development. I am working with the nus service for communicating but now i also want to have ota firmware update. I am trying to...
When running the light_switch provisioner example, the application fails to the error handler when calling app_default_models_bind_setup, in access_model_application_bind...
Hi,
we are developing a device with 2 µC one being the nRF52832 for BLE connectivity. We want to do DFU via BLE with our own protocol. From what I've read, in this case...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As hardware I am using the nRF52840 Preview Development Kit. As software basis I use the ...
Hello, a couple of get-me-pointed-in-the-right-direction questions, if you don't mind.
I plan on creating a system with an accelerometer that talks SPI to my Nordic nRF52833...
Hi!
I read that your Thread stack uses a different 802.15.4 implementation than the MAC driver. Is it possible to intercept special broadcast data packets e.g. from energy...
