Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello everyone,
We are 4 students, who are developing a BLE mesh network to send data from a CANNBUS-simulator to a desktop. We have chosen to use the nrf52840 chip to set...
Hello,
I am using nrf52832 with SDK 16, I want to change advertising packet flags from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE(0x05) to 0x04 during run time how can...
Hi, Im developing an ac dimmer with zero crossing on mesh, but it flickers at low dimming levels, I even used the scheduler for the ble stack but it didnt help, what would...
hi, i am using nrf 52840 dongle , is there any support of AT commands to communicate with dongle .i want to communicate without using ui only by sending commands. if not any...
Hey Nordic Team!
My requirement:-
Sensor data----------------------------->nrf52832------------------------------>Raspberry pi 3 (via blue tooth)
Is it possible...
We are working on external RTC MCP7940(i2c) interfaced with nrf52840. Please check if drivers of the same for nrf52/51 are available or any implementation of CLOCK using MCP7940...
Hi,
I tried to add 3 characteristics and 1 gatt service to my NRF52810 using with development board with 10040e (I am using gcc compiler). Then I got a error which is saying...
we are considering using .005" thick stainless steel to provide better bridging effect across the opening on the board for the battery. This will provide more strength to...
Hi
I am trying to use an antenna switching board for AoA direction finding. I know that the RADIO controls 8 PSEL.DFEGPIO pins to control switching antenna.
1. Could...
Hi,
We want to use the NRF52810 without radio and we don't want to put the external oscillator to reduce the PCB size
I would like to know if necessary to have the external...
Hi,
Some time i could not put break points inside main for sample projects provided for nRF91, i tried clean build, erasing the flash 'nrfjprog -e' and evn enable the configuration...
We would like to use a Dongle based on the nRF52840 as a BLE Central communication via NUS to our product. The example in the nRF Connect Desktop does just wat we need on...
Hi，
I want to use none secure example on nrf5340.
The code can't run with ns config(uart didn't log anything),But it works fine with normal config.
How can I sovle this...
Hi, devzone.
Since I was recommended last time, I started reading the BLE tutorial .
I first saw a this tutorial .
Even if nrF52-ble-tutorial-advertising is placed in...
Hi,
I have a custom nRF52840 board. I mistakenly tried flashing the custom nRF52840 board with STM32 firmware. From that moment on, I can't flash board. When connected...
