I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi,
I am using a ble_app_blinky example (SDK16) to communicate with the BLE devices. NRF52840 is connected with the client devices and successfully sending the data to the...
Hello,
I would like to know if it is possible to not use softdevice because i need more flash for my code. I guess it is possible but when i don't enable softdevice in my...
Hello,
i'm trying to use SPI with nrf9160DK as master and RFM96 module as slave. At the moment, i'm developing elementary functions to write and read from my slave device...
Hello
I am working on Nordic nrf52832
I am using the "ble_app_blinky_c_pca10040_s132"
I want to use ble for scanning a beacon (eddystone TLM) and collect its data. ...
please help. I need functional description of what is need step by step for doing a zigbee hardware device switch and management over bluetooth on the thingy52, i have all...
Hi Team,
We are using the NRF52840 with s140 Soft device for our BLE application.
While we are facing some issues while doing debugging.
1. We are getting Hard Fault...
Are there any issues of pairing a nRF52833 using OOB pairing with a IOS device? Is there a good example code I could start with?
Thank you very much.
All the best
P...
The system requirements: 50 identical nRF53-based devices (each with a sensor and an actuator), positioned within a 3x3 meter square should be connected to a single computer...
Edit : The code posted below works on the 96x96 3V(LS013B4DN04) variant of the display, I still have no idea why it doesn't work on LS044Q7DH01, but I'm guessing it doesnt...
Hello!
I have some devices with a custom built PCB on my desk, all of which have my own custom firmware on it.
Sadly the devices don't have access to the debug pins...
Hi Team,
May I know the functionality of the below mentioned signals:
MIPI RFFE interface pins: VIO, SCLK, SDATA. MAGPIO interface pins: MAGPIO0, MAGPIO1, MAGPIO2. ...
Hi,
I got a question on nRF52832 platform. When it is brand new (so without loading any of our FW) and powered through 3V3, it draws up to 4.6mA when powered. But we also...
Hello,
We have seen the below error,
NRF_ERROR_INVALID_ADDR If the EasyDMA is used and memory adress in not in RAM.
While trying to connect with an external sensor hub...
Timer A with a 10-minute interval, timer B with a 4-hour interval, and timer C with a 10-second interval are required, and A and B should also run out of time in low power...
Are there any updates on coded phy support for the nRF sniffer?
I found a thread about this from "over a year ago" which says to check back in 4-5 weeks: https://devzone...
