When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have a customise board which has nrf52832 chip inside. I want to establish a secure connection between my 2 customised boards but I dont have any button or display...
Hi,
We are currently in development of a custom board with an nRF52840. I'd like to check my IO pin mapping using an IDE if possible, but I was unsure if Nordic or its partners...
Hello. I am using a Nordic Semiconductor Beacon (nRF 51822) and i am trying to connect it to my Raspberry Pi 4, but even though i installed Bluez, scanned using hcitool, i...
Hi,
I have nrf9160 DK. It is ok for ibasis SIM card. But if verizon SIM is used, there is no TCP/IP connection.
I tried to set APN by using:
AT+CGDCONT=1,"IP","vzwinternet...
Hi,
I'm trying to deploy the example program, cifar10, from CMSIS-NN library on NRF52. The issus is I compiled and downloaded it to the board successfully but when I try...
Hi,
I'm trying to combine serial UART functionality into the USBD_BLE_UART example. The goal is to send data in/out to the hardware UART as well.
I started off by loading...
Hello all,
I am trying to get the address of the scanner sent a scan request to my nRF52840 running as a peripheral and advertising. I am using SDK 15.0 and I have tried...
I have modified Android_nRF_Blinky to show the status of a sensor along with a timer. I added an alarm notification to be popped up if the timer is overflowed and it is working...
Monday: I received the 52 and upgraded the software to the latest release (2.2). Loaded the Thingy app on Android 10 on a Samsung S10 5G. Changed the name of the Thingy to...
I need to store some data into the NVM of nRF52832 , which can be saved after powering down . In nRF5_SDK_16.0.0_98a08e2 , which example should I learn ?
All examples of...
Now I can only download the 《nRF52832 product brief.pdf》 . The link is shown below:
www.nordicsemi.com/.../Getting-started
However , this data sheet is not complete ....
Hi,
I'm using an MS50SF1 nrf52832 3rd party module. I successfully programmed it through nrf52 DK.
After program that module, I was able view it through nRF Mesh App ...
Is it possible to update from 6.1.1
To 7.0.1?
New softdevice does not fit if linker file FLASH address starts at 0x26000, that's why increase to 0x27000. ...
