Hello!
I have tried in various ways to make the XIP part functional on SDK version 3.0 (SDK v3.0.0-3bfc46578e42) but without success, this on the NRF5340 devkit. I mention...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
When trying to configure custom UUID the nRF Connect, the program fails to find the location of the file.
This is due my username to be "Filipe Aguiar" with a space which...
Hello, Nordic community,
I built and successfully run mqtt_simple project on our MQTT broker using v1.1.0 firmware and NCS.
I edited CONFIG_SERIAL=n in spm and mqtt_simple...
I have one of the nRF52840-preview-dk boards. When I brought up nRFgo and clicked on the board, I was invited to update the JLINK firmware. It was pretty enthusiastic in its...
Hello,
I'm trying to use the zephyr settings module to save bluetooth settings on the nRF9160 DK. I'm using the NCS downstream version of Zephyr . Unfortunately in the most...
1.when i use the example on the dir : examples\ble_peripheral\ble_app_blinky\pca10056\s140\arm5_no_packs
i have sucess flash the softdevice and the app:
the console show...
Hello ...
I'm adding buttonless DFU support to my nRF52810 application using the instructions here . I'm using SDK 15.3.0, SD 112 6.1.1.
First question: These instructions...
I'm using the SPI Manager to send large transfers of data to a graphics controller. What I see is that, once a single byte is transferred, the CS line will continue to pulse...
Hi,
Greetings!
I want to disallow an unknown bluetooth device (like phone, etc) to connect to "secure_bootloader_ble_s132_pca10040" except from a bunch of pca10056 (central...
Again, I'm having trouble with the driver library. Earlier when testing I had SPI working OK as a small standalone test , but now I want to add SPIM to my actual application...
Hi,
two days ago I started checking the usbd_cdc_acm example in order to add usb serial comm functionality to my project. and I have some fundamental (newbie) questions...
Hi all,
I'm trying to add to our application BLE DFU feature. Therefore I'm testing first the secure bootloader example provided in the SDK v16.0.0
I managed to build...
Hi!
I have been using and loving the simplicity brought by the Toolchain Manager (TM).
But now I want to use an application available on the master (Connectivity Bridge...
In an attempt to add a custom UUID to your current project I change NRF_SDH_BLE_VS_UUID_COUNT from 0 to 1. Then loaded the code onto our PCA100040 53822 devkit. At runtime...
Hello I have a nRF9160DK V0.8.5 and downloaded the latest User Guide (V0.9.2) but it does not match my board. Looking at the Revision History section of this document it looks...
Hi!
I've been playing around with the SDK and nrf9160 dk for a week now, and it's a lot of fun.
In the beginning the UART example worked perfectly, and I managed to add...
