Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hi
I have a simple question which I am not able to figure out.
How do I use the nRF52833 DK without having it plugged to the computer. I tried switching the power to...
We are using a flash part that is 64 MB in size. It is S25FS512. We are trying to use 32 bit addressing mode by setting sdk config flags. However this does not seem to work...
Hi,
Greetings!
I just tried Low Power Node example application from SDK for mesh 16.0.0
It works functionally well, however I am little curious to know below point(s...
Hi,
I start developing with a new MacBook Pro (2019) which only offers USB-C ports. Currently I am facing the issue that the Programmer App does show the connected Thingy...
Hi!
I have recently setup the development environment for my Thingy 91 on Windows 10 environment using nRF Connect Getting Started Assistant. But I am having some trouble...
Hi, I am working on nRF Thingy52 for a week. I am having SES with SDK_16.
I am having 3 nRF thingy to do a testing purpose
First i need to analysis how the thingy works...
I'm testing using the internal RC circuit to drive ble via the S132 softdevice. Set up is with Nrf52DK and Power Profiler kit. I got everything running and was measuring about...
Hi, How can I configure the LwM2M server (URL, Port, Credentials) on my Thingy91? Can I do this via MQTT and the nrf Cloud or do I need some specific tools?
I have a GT832C.01 (Bluetooth 4.0 BLE sensor detection module BMX055 9DOF NRF52832), I don't know how to program it, I can see it from the phone, but what software do I need...
I have a BLE board with a nRF52832 and some peripherals. It came with a preinstalled bootloader and firmware (the bootloader supports DFU via BLE to upgrade the bootloader...
Hi,
I am completely new to this technology,I need to interface BME 680[humidity,pressure,gas,temp sensor] with Nordic nRF52840 - how it is possible,i want know the hardware...
Hi,
I am using nRF52832 DK, with Segger Embedded Studio as IDE. I am using ble_app_uart example. I have used an encryption algorithm. The encryption algorithm is called...
Hi,
Does the SPIS generate interrupt for every byte of data receive ?
What kind of interrupt of event that SPIS will generate for data received ?
Please advise
Hi,
I need to assign Rising edge and Falling edge event in a single pin.
I try to assign both Rising Edge and Falling Edge event into APP_EVENT_PIN.
There is a error...
