Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi Everyone I am trying to get a hold of the nrf9160 SDK which is based on zephyr. Here is what i would like to know 1. There is a file named zephyr.dts which has all the...
Hey guys, I've been trying to do a range test with 2x PCA10056 dev kits. I believe I've set everything up correctly and cannot achieve more than 300-400 meters before the...
If we input 5V DC supply to Vin 3-5V P20, the Bluetooth programming failed at start. But if we input 3.3V DC supply to P21, the Bluetooth programming passed. Is this Vin 3...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
It seems that the route is decided by the leader, can I specify the route?
...
I am making a simple breakout board for the nRF52833 (I'm using Fanstel's BM833 module). This is what my board is looking like. There's a ground plain on the top and the bottom...
I'm trying to send data from a NUCLEO F401RE board with the nRF 52840 DK using UART. Then have the data to be sent to my phone via Bluetooth. I'm starting from the ble_app_uart...
Hi Devzone:
I have a question that may be common for companies distributing hardware containing nrf52840 chips.
I have figured out how to use nrfutil to generate Bootloader...
Hi there,
I connected my nRF5340 PDK to an external target - which was unluckily defective.
Since the external board had its own power supply, there was now either an...
Hello,
i have built my own custom service.
I have 13 characteristics ....
But in NRF Connect on an iphone, i can see 13 characteristics , but only in the first there...
Hi
Technically this is a Zephyr question, but googling the issue gave no success. Also, reading the Zephyr docs gavve me no clue.
I have a custom nrf9160 board with an...
I'm trying to capture events like accessing an invalid idx of a C++ vector
I'm using the method at , like this:
std::vector<int> my_array;
my_array.at(10000);
...
Hi,
I want to use the SAADC to measure the voltage on the VDDH pin. I am using a design based on circuit config #4 and following the SAADC example in the SDK version 15...
Hi,
I am using nRF mesh Android app version 2.1.4
I have flashed the devices with light-switch example application under nRF5 SDK for mesh V 4.0.0 on PCA10040 DK. I'm...
