after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am now in Hong Kong, and trying to connect to NB-IoT network here. There are 2 providers of NB-IoT in Hong Kong: "CMHK" and "Three". They provide NB-IoT since 2017...
Hi!
I was testing the SD Card example that is available on the SDK 13.00 in the following path: "nRF5SDK1300/examples/peripheral/fatfs". I checked SDK 16.0 and the code...
I have a hard-to-reproduce bug in my MQTT application that I have investigated enough to realize that my MQTT thread is stuck in a call to mqtt_publish(). I've verified that...
I would like to add UART as an option to the "ble_app_hrs_rscs_relay" example in SDK16, But keep the peripheral low power.
i.e. once I set a GPIO, the UART will start to...
I'm working on a project where UART0 is used as a nrf logger uart back-end. Recently I've tried adding UARTE1 to the project to implement additional serial communications...
I am unable to initialize soft device, but I am able to initialize log, led, gpio and timer as well, I can see debug prints as well. After debugging I found following information...
Hi everyone,
We are developing switch product which running with Android Application.
We have problem about send status from switch Device to Android Application
+ Android...
Hi ,
I have tested two boarrds(PCA10040) with same application id and higher application version,These work well done.Then I want to test mesh DFU Relay function,However...
Hi
I re open an old ticket to know about changes in the Android Mesh Library
https://devzone.nordicsemi.com/f/nordic-q-a/45553/is-sequence-number-and-transaction-id-equal...
I had a awesome trouble with the ble when update my firmware, with the same code in app and firmware, the samsung s10(android 10) and s7edge(android 8.0) can send 510+K files...
Our BLE HID mouse devices has work well during several months and since some windows update, on some PC, the BLE is disconencted every 30 sec.
We received a BLE_GAP_EVT_DISCONNECTED...
I am working on a project that is based off the Nordic Thingy-52 design. I have run into a problem that I was hoping someone might give me some help on.
When I designed...
Hi,
I'm testing a couple of EVBT840X boards from Fanstel which includes a PA + LNA within the nRF52840 module.
The source code is based on the ble_zigbee_dynamic_template...
I am trying to use the fds example provided in the sdk16, while viewing the debugging prints I see the following,
<info> app: Initializing fds... <info> app: Event: FDS_EVT_INIT...