I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
Good day! I hope everyone is doing well.
I have a weird problem measuring Li-ion battery pack voltage.
Problem: Tried to measure battery pack voltage 12.6V using...
We're struggling a bit with our NFC implementation. We were using the T2T library, using the examples, and it was working fine. However, we saw current drain at ~ 400uA, which...
Currently I am testing the coap_client and https_client sample application with nrf9160 based custom board. But the board is continously resetting while searching for the...
Hi there,
I was wondering how the motion pane is supposed to work in the bifravst app, it doesn't seem to be refreshing. The battery pane doesn't seem to be refreshing either...
Hello.
I'm reading the documentation of the radio peripheral of nRF52832 but I can't find any information about the S0 and S1 fields.
What are those fields? What do they...
Hi, guys. I'm using the PCA10056 and the SDK 15.3's BLE UART peripheral example. I'm working on a PWM controller using the mobile app.
I need to create a delayed PWM signal...
My current project is to build a simple BLE LED controller. The goals of this project are to familiarize myself with lower level modules and to practice designing/building...
Hello,
I'm trying to create a project from scratch and write my own drivers. I have strong background in C but unfortunately I don't know anything about assembly. I could...
Very strange, I have lots of nRF52x experience, but this one has me stumped.
Successfully updated our custom board/application from nRF5_SDK_15.0.0 to latest as indicated...
Hi all, I apologise for this very basic question, but I don't understand how to add/enable RTT debugging to my code. I want to practice writing basic code for the NRF5 SDK...
Could you please advise me regarding BLE security?
For security purposes, UUID data shouldn't be included in the advertising data package?
If we don' t put UUID in the...
Hello
My custom board has only 1 button and I'm trying to detect 3 button clicks. The first click is waking up the device and the other 2 are configured as BSP_EVENT_KEY_0...
I have a setup similar to this
When the callback is executed, the execution will enter the inbuilt_key function and then the output will stop and the execution will halt...
I'm using v1.2.0 for the nrf project and I am fairly confident I am using modem firmware 1.1.1 (though I don't know how to verify that).
I'm basing my project on "cloud_client...
Hi,
I am evaluating the ble_app_hrs_pca10056_s140 project with nRF5SDK160098a08e2 Dev kit and nRF82540 dev board.
I have put a breakpoint in line:
*p_erase_bonds = ...
