I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I use Peer Manager for storing bonding infomation with nRF52832 (SDK14.2) using gcc.
I understand Peer Manager uses FDS, and FDS uses flash memory from 0x7D000 to 0x80000...
Hi All,
I know this question seems to have been asked many times already but still does not seem to work for us even after checking forum answers.
Hardware: Fanstel BT832...
I have followed up this example and compiled successfully but the NFC pairing is not working at all.
I use my smartphone (Google Pixel 2) to touch the NFC antenna and nothing...
I can control GPIO P0,but can't control P1, when I load project with nrf5340_dk_nrf5340_cpuapp ns configuration.
If I load project with nrf5340_dk_nrf5340_cpuapp configuration...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board to connect with an iOS(v 13.3) phone.
I am running a custom application which uses the...
At this time my project is at very beginning state, I am picking up right tools to start my project development. I have spent good amount of time to research about my issue...
Hi,
So simple question about adapting dev kit examples for the dongle. I'm trying to adapt this USB/BLE example and I've made all the changes that I figured I'd need to...
Hello,
I'm currently levelling up a project based on an older SDK which involved SoftDevice v5 (S132) to SoftDevice v7 (S140).
As far as I understand S132 and S140 are...
Hello,
following the peripheral/saadc sample, which shows the periodic reading... could you please share the essential and minimal config for the One-Shot measurement? ...
I want to integrate the XMOS (XUF216-512-tq128) with nRF52840 where the nRF can be used to perform the field updates for the XMOS. Is there an application note or an example...
hello,
i am using nrf52832 device with soft device of S132.
i am trying to connect 2 different applications on the same smartphone to the peripheral device. currently...
I have two NRF52840 dev kits that are running what are essentially the spi master and spi slave examples. They both work and I've altered them slightly. I'm just kind of confused...
Hi,
I've been trying to combine the spi_slave and USB_CDC_ADM examples so that I can pipe data from a spi_master all the way to my host machine. In my cobbled together...
Hello ,
Is there any development KIT available for the Evaluation of Direction FInding - AoA and AoD ? Any code examples for the same?
If not what is the time line?
...
