Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi,
I`m considerate to use Nordic SoC in my design.
Please advise if Nordic have BLE SoC with Capacitance Touch Sensing capabilities like in Cypress part CY8C4127LQI-BL483...
So, I am adapting and adding to a project based on the example app with SDK16.0 and softdevice s112. I'm using Keil.
My nrf52832 has 256kb flash, 32k ram.
I'm compiling...
Are there any examples of how to configure the COEX pins between the 9160 and a 52840 such that each will actually use the signals to start/stop their respective radios? The...
I see references to a get (0x8046), set (0x8047), and status (0x8048) messages for Node Identity. Where could I find documentation about these messages? There is no sample...
What is the purpose/functionality of SWO pin (pin 6) on the Debug In port?
I see it connected to P0.18 on PCA10040 and P1.00 on PCA10056, but I’m developing custom board...
Hi,
Though I could able to successfully provision light and switch using nrfMesh Android application with all elements being configured and also could publish/subscribe...
Hi,
Recently, I am studying the blog as the link below:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/bluetooth-prepairing
We would like...
Hi all,
On the iOS version of the Blinky APP, there is a statement
Created by Mostafa Berg on 01/12/2017. Copyright 2017 Nordic Semiconductor ASA. All rights reserved...
Hi,
I am using pin 27 as SCL and 26 as SDA on my custom board which is working on 1.8V.
There is no activity on SCL pin, while i am getting correct values on SDA pin when...
How can I read the ICCID (Integrated Circuit Card ID) of the SIM-card?
Normally (with competitive modems) I get the CCID by AT+CCID.
The nRF9160 reponds with +CME: 0 ...
Hi, I would like to develop a BLE central node that sends over UART when a button is pressed. I understand the memory is limited on nRF52810, but I think it'll fit. The example...
I am developing on the nRF52832. I just discovered that if my program enables Access Port protection by writing the UICR at runtime, then the program can still be read out...
Hello,
I want to use a third party bluetooth module (based on Nordic SOC) in my application, so far my understanding is that using your softDevice stack I have to implement...
Hi
My Thingy:52 works perfectly OK with Thingy app on my iPhone.
However when I use the Gateway on my iPhone and then nrf cloud I get an unstable connection on the cloud...
