Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
For our current application we are using NRF51822, SDK 6.1, Soft device s110 ver 7.1.0.
In our application nRF is configured as SPI Slave and another controller as SPI...
Hi expert,
I am developing 51822 under SDK 6.1, and we have one button and some sensors' interrupt lines as input GPIOs in our platform. In my code, after calling gpiote_init...
Hi there,
I am trying to send six 20 byte packets per connection interval. Is changing the length of charecteristic simply
attr_char_value.init_len = sizeof(uint8_t...
I have set up a board using device_manager_central to connect with BTLE sensors. I have used a combination of the multilink example and the heart rate collector example along...
Hi,
I used nrf51822- EK board.
GATT - s110 6.2.1 softdevice
I transfer data through UART for nrf51822-EK(PCA10001).
But this time. I used nrf51822 smart beacon...
I develop with nRFgo SDK 2.3.0.10040.
Normally PRX can communicate with PTX by auto ACK, but when there are two or more PRXs with same configuration exist, once PTX sends...
Hi all,
I am trying to use for the first time my nRF51822 development kit, following the "Development Kit User Guide v1.3".
The problem is that when I open "nRFgo studio...
Do all revisions of nRF51 have the same 4kB RAM sections with separate RAM AHB slaves? The product specification clearly states that only for revision 3 chips.
Not really a question, but it took me way to long to find out about J-Link RTT (i.e. j-link Real Time Terminal for easy debug printing so I thought I would mention it for...
I need a fixed voltage reference on my circuit. Since nRF51822 has internal 1.2V voltage reference, I am just wondering if there is a way to use this reference for external...
Header for nRF51 (nrf51.h) mentions two peripheral blocks completely missing from chip documentation. Are they functioning? If so, the comment for PATCHADDR field of PU says...
Hi there,
After prototyping a device with modules and on a breadboard, I transitioned to a custom PCB with nRF24L01+, matching network from the spec sheet, and 2.45 GHz...
Hi everyone
now i used softdevice s120 scan and connect two s110 device
and i used sd_ble_gap_rssi_start() when connect event ,
then get the rssi in BLE_GAP_EVT_RSSI_CHANGED...
HI,all!
Recently my nrf51822 device encountered a tough issue,the detials are:
My device connected to an android app, which has some bugs about ble connection so the...
