Hello, I am encountering an issue while setting up an OpenThread Border Router (OTBR) using the following hardware: nRF52833 board (flashed with RCP firmware) nRF52840 board...
Hi
custom board using the nRF9160, toolchain version v2.6.0, mfw_v1.3.6.
Sorry I can't provide a decrypted modem trace, but I hope the screenshots are enough to show what...
Hi, I am working with nRF52 DK (52832), and the issue I am facing is that i am unable to increase the data size of data SPI -DMA can receive. Currently it is configured at...
Hello everyone,
I want to evaluate the power consumption in idle mode of the nrf9151 sip.
Environement:
nrf9151dk_rf9151_ns
nRF Connect SDK Toolchain v3.0.2
VScode...
I’m using SMP over UART to send the erase command ( {"slot": 1} ), and it only erases the application core image (image 0). I also have a network core image (image 1) present...
So i am currently referring this ticket and from that I get to know that when when setting parameters for create config (HCI_LE_CS_Create_Config) command for channel sounding...
I am trying to get the lowest possible power consumption for my Thread device, so I am experimenting with different configurations.
Currently I'm testing with SSED ( Synchronized...
I have custom board with nrf 52832. I am using SDK 15.2.0 and softdevice s132 V6.1.0 to transmit advertising packets periodically. I have written simple application that reads...
We use nRF52840 chipset to design a BT module, and it went into pre-production now. But we found the RX sensitivity is not good. We need your help to confirm the RX sensitivity...
So I am using nRF52811 and I have noticed the battery voltage going at a constant rate and suddenly for a time of 2 mins the Voltage value (ADC) dips and it comes back to...
Hi,
I read many post on devzone, but still not familiar with programming "custom board" in my case, board from Sparkfun. My Sparkfun is correctly connected to nRF52832 DK...
Hello,
I am working to replace my BM70 with nRF52 series. So it has to be quick and simple solution. So, I used nRF52840 USB dongle as my slave (Peripheral Example code...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Is there a way to know the cause of the reset?
I connect the PC to the device and run it in debug mode. However, nothing is written...
I'm running SDK 15.3 with SD 132 and SES 4.30.
I am working with the ble_app_uart_c as the base code and adding other functions. I've gone through the app_timer tutorial...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - Chip) and Nordic SDK v.14.2.0. Now I try the SPI example and I don't know which register is adressed in the last...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
This issue is similar to below ticket with -eraseall and chiperase...
Hello,
Im configuring ADC on 3 channels. However during debugging when I stop Keil I see that in all channels the acquisition pin is the same AIN1.
Any idea why is this...
Hello, I found an examples using ble_app_uart and and MPU6050 from different SDK's. I am trying to update the to SDK16 and have got it to build successfully but when I try...
hello
I'm testing DFU example.
I'm Using nRF connect v3.2.0 & J link 6.44g( The same happens with the latest version. )
Why this error occurred?????
This error occurs...
Hi,
I want to implement a I2C on my thingy91.
As I am completely new to the world of nordic, I just had no idea where to start, but after reading a lot I thought I could...
