Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
The Nordic Uart service for peripheral devices has a function ble_nus_init() which takes a callback function in a struct.. Later on this callback function may be called with...
I am doing the project using nrf blinky.
My phone cannot find the nrf52840 . Before this it is ok, but now it cannot discover it . I notice that LED05 is blinking very fast...
Hi guys ,
I am trying to connect thermistor with the ADC pins of nRF.
I use the steinhart formula to calculate the temperature in degree celcius. I used a voltage divider...
I have a development environment using Zephyr; setup and working from the documentation I found for the nRF Connect SDK. I am using SES and am able to debug the provided examples...
I am writing a Windows program to control an nRF52840 using pc-ble-driver, v4.1.1, with NRF_SD_BLE_API=6
I need to do all of the following:
1. Scan
2. Create multiple...
Hey guys (and merry Christmas),
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I try to receive data...
Hi,
I try to modify ble_app_uart so i can get a feed back from the boar if send something I use switch case for my use case, I'm working with eclipse
here what I do...
I have been working with the thingy91 source code from ncs, I can compile and load the sample app successfully. However I did notice that when I compile the code it does not...
I tried out DFU functionality initially using nRF52840-PreviewDK and UART transport
When downloading an app via DFU, It takes about 6 seconds from the time I start nrfutil...
Hi,
I am trying to make my own border router for Thread mesh network using nrf52840 and BG96. I have ordered pre-certified third party modules. Now How can I interface it...
I can't seem to find a data sheet on the PMIC used on the Thingy91.
The data sheet shows a ADP536x and discussions call out a ADP5360.
I searched the ADI website and did...
Hi all,
I am trying to test the OpenThread protocol by using CLI example.
Path of example is nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31\examples\thread\cli\ftd\usb...
Hi,
We use the nRF51 (nRF51822) on our products with the S130 SDK 2.0.1. In order to update the BLE application that we developed, we use the bootloader (secure bootloader...
Hello,
we are would like to drive 3 shift registers simultaneously using QSPI interface. We have look through QSPI examples but it looks like all examples are build around...
