Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
HELLO ALL,
I'M TRYING TO TEST THE BSC Rx EXAMPLE FROM DE SDK V16.
WHEN I DO IT USING ANTware II, EVERYTHING IS OK, SINCE IT'S ENOUGH WITH CONFIGURING CORRECTLY CHANNEL...
Hello,
This is a followup question regarding this old thread I started: https://devzone.nordicsemi.com/f/nordic-q-a/48295/hold-output-pin-during-bootloader-jump
IC: NRF52840...
Hi,
I'm relatively new to your product line, but have been spending a bit of time trying to bring the volume control functionality into a SDK16/PCA10056/s140 configuration...
Hi,
I am using SD calls to start an advertisement of BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED :
sd_ble_gap_adv_start(m_adv_handle, APP_BLE_CONN_CFG_TAG...
Hello, I have a project that's fairly mature and working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a million...
Hi
I plan to use nrf52 DK to program my device by using a connector https://www.tag-connect.com/product/tc2030-idc-nl
But should I connect it to debug in or debug out...
Hello,
background: using Keil IDE, my own board that has a nRF52840 on it. My goal is to create automatic DMA transfers from SPIM3 peripheral.
I am setting up EasyDMA...
I'm porting a working app from SDK 1.1 to 1.2, and have noted that when I make an mqtt connection close it, and re-open (to a different mqtt server) that the call to nrf_connect...
I have reviewed most (if not all) posts on this forum that relate to multiple vendor specific UUIDs but still see issues on my platform.
I am using nRF52832 (with minor...
Working with nRF9160 running west build -b nrf9160_pca10090ns. I get an error FATAL ERROR: command exited with status 1: /home/ahmed/anaconda3/bin/cmake -B/home/ahmed/nrf9160...
Hello,
I tried to implement my own "Vendor model" by ( Documentation ) given. I am using example code from documentation. Using mobile app (nRF Mesh) I type optocode of...
To the kind attention of Nordic support team,
I'm interested in a ble example (SDK15.2 nRF52840 nRF52832) where peripheral device is waken up from being in deep sleep mode...
Hi,
I am working on the client program to retrieve the value from 4 characteristics at the same time using notifications. I have already done with the server program. Using...
Hi
I am trying to use the serial library with IRQ and callback function, but the event NRF_SERIAL_EVENT_RX_DATA is never triggered. No other event than NRF_SERIAL_EVENT_TX_DONE...
Hi support,
I'm currently using pca10040 on my custom board and want to be able to implement the CLI over uart port. My SDK is 15.2.
To get started, I test my board's...
