HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I like to understand what SBs should I cut, what switched should I use to measure the SOC current only with PCA10056 board. I use the Otii Arc device to supply power...
Hello,
I'm working on NRF52832 based module BMD-301
for same i'm using SDK16 Segger Embedded Studio
The thing is
when uploaded ble_app_alert_notification example it...
Hello,
I've tried to convert the mesh light switch server example from NRF52840 DK to Dongle following this post.
Unfortunately that doesn't work.
I've changed the BOARD_PCA10056...
Currently, there is a project. The situation is that the master nRF52840 communicates with the cloud server through the GPRS232 module, the slave nRF52840 communicates with...
Hi,
I tried to create a custom server in using server setup of nRF Connect v3.3.0 but when I tried to apply my custom server on my device, the software bugs instantly. ...
I want to modfiy the code in the example ble_app_ancs_c to read the internal flash with fstorage. But after I set APP_TIMER_CONFIG_USE_SCHEDULER to 1, the operation of fstorage...
Hi every one, I am running light switch example (using SDK 15.2 and SDK for Mesh version 3.1.0 ). The problem is: My provisioner node cannot Receive RSSI message of a node...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
My custom function for saving is:
I call the function using below...
This error always stop the "mqtt_simple" application.
I have tried modem versions 1.0.1 and 1.1.0, SDK versions v1.0.0 and v1.1.0 and added this code to system_nrf9160.c...
I have an Android application running with RxAndroidBle library and I want to change it to Nordic-Ble-Android library. I'm not that good with Bluetooth and the actual version...
Hello, i'm new in BLE and i would like to know, what is the best way to read and write 200-300 parameters of my product via BLE from a phone?
Possibility 1 is, to create...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
Is this correct by populating the record as such?:
And to read...
Hello,
is there any tutorial on how to send commands to the Thingy52 from an Android app (like the Thingy52 app or nRF Connect) to start the RTC clock (and then read/clear...
My 52833DK is apparently bricked. I get the message "Could not find core in Coresight setup. Abort debug session” When I try to load code (IAR) into the board. It was working...
Hi
I'm trying to understand the files outside the main program. The files that are at the samples path. Like "CMakeLists.txt, Kconfig, proj.conf, sample.yaml etc". So from...
