Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi i want to send a string using uart over bluetooth. For a try i compile ble_app_uart and flash it to my dk but i can not see the message on the terminal neither in Putty...
Hello everyone,
I am using nrf52832 module with SDK v14.2 and SD v5.0.0 for my development.
Recently, i started facing the below issue:
Once i try to pair the module...
Hi Great QA team:
Our client has made their product in MP stage but found out that some of the ICs with FDS Bug (Base on SDK 15.2):
REF: FDS - data corruption https:/...
Hello,
Quick question.. we are working on a board and running very low on GPIO pins. It would be helpful to remove the low-frequency (32k) XTAL, to recover those pins. The...
Dear,
I am testing with thing91
todo: read and send the temperature to my webserver in each 15mn
using: thingy91, LTE_M
sample1: in the fridge (4C)
sample2: in...
Dear community,
I am developing a firmware using SDK 16.0.0 which handles interruptions from an accelerometer and a timer.
I've built on top of APP_UART lib a set of functions...
Hello,
I tried to use use pc-ble-driver for Ublox NINA B3 EVK which has nRF524840 .
It failed with following error:
./heart_rate_monitor_v6 /dev/ttyACM0 Serial port...
Hi everyone,
I am using "nRF5 SDK for Thread and Zigbee 2.0.0" in my project , that includes the libraries of OpenThread (commit 704511c96e0d093139e4b80ef0739ed2d701afb1...
Hi there, currently I'am designing a circuit for nRF9160 inspired by Thingy:91. About Thingy's antenna tuning (Thingy:91 User Guide page 16+17) I have some basic noob questions...
hi guys,
I was just getting started with Nordic nRF52832, I want to find buffer containing bluetooth scanning data (Beacon) to process but see the examples but can't see...
Hi there,
I added the GPIOTE driver for the project ble_app_blinky_c under the SDK13, where if I enable GPIOTE my current consumption in sleep mode jumps from 3uA to 5mA...
Hi,
I am writing C/C++ programs running on open-embedded boards to talk through pc-ble-driver (v4.1.1) to bond (Security mode 1 level 4) with PCA10040 or PCA10056.
I found...
Hi,
Iam using the nRF52840 DK to make this as a bluetooth LE controller. By following this link https://infocenter.nordicsemi.com/topic/nwp_029/WP/nwp_029/building.html...
Hello -
We are using the nRF52840-DK with the 15.3.0 SDK on FreeRTOS. Our application is configured for tickless idle and based on the ble_app_hrs_freertos example. I...
