Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
We are using nRF52811 for one of our upcoming product. We plan to upgrade our firmware via DFU. I cant find any support or example codes for this controller for DFU...
Hello Nordic Team,
Currently I'm working in a BLE HID Project (joystick with 16 buttons and 2 axis (x and y)) usign a NfR52832 and modifying the hid mouse example from SDK...
Hi,
As well know, the nrf52832 had build-in a battery level detect function. It can get battery-level by following program
Would you please tell me how to design it...
Hi
When I finished the program and read back, I saw that there was unintentional data at 0x2D000 and 0x2E000.
I used up to 0x26000 addresses. Where is this memory used...
I've taken the basic examples/peripheral/blinky code and tried to add the logging module to it. For some reason the only time I can get the application to run and log correctly...
I am developing a firmware application that needs simultaneous central and peripheral role. I am using sdk 15.2.0 and was experimenting on dev board PCA10040. I have taken...
Hello,
I want that nRF9160 goes into PSM on boot until a button is pressed, do someone have a good link about PSM please ?
How can I do a software reset with a clean lte...
Dear people,
I use a pca10056 (alternatively the pca10059 dongle) and have compiled the connectivity firmware as described on the github page (release 4.1.1).
The only...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\serial and board pca10040.
Supported commands.
In [2]: for i in range(0, 10): send(cmd.Echo("Hello: " + str(i))); time.sleep...
Hi, I'm reading the nRF5340 OPS v0.5.1 document and in section 3.2 ("Memory") there is a reference to "256kB of peripheral RAM". However, the document doesn't explain what...
Hi there,
I'm working on nrf82382, try to use COMP function to monitor the voltage of AIN0(p0.02), but seems not working, no example for the COMP. and then I found the...
We enable TX notification of NUS service with bonded iOS (iPhone), iPhone constantly sends TX_READY command until disconnect.
Can you confirm this is correct behavior. ...
Hi, I am working with the adxl362 sensor and the nrf9160 SPI example ( https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/spi/src/main.c ) and...
Hi, I am working with the adxl362 sensor on the Thingy91 and I want to set the trigger of the sensor to a specific value.
In the datasheet ( https://www.analog.com/media...
