I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
How can you use assisted GPS(AGPS) in nRF9160?
Let's say you get assisted data from "supl.google.com" and how do you set this address in code?
Do you have to wait for...
Hi
I am using nRF52832 DK, with SES as IDE on Ubuntu-16.04 OS PC. I want to stream some data from PC to DK. The DK is connected to PC for power supply and programming the...
Hi there,
I'm struggling to get a DFU over serial done. I'm using a nRF52840-DK (PCA10056), the nRF-SDK 15.0 and nrfutil 3.5.0.
I
- genereated the key pair,
-...
We have a product with a microphone with PDM output that uses the nrf9160. The nrf9160 does have a PDM hardware unit that looks well suited to read it out. But currently there...
Hi Community Members,
I have a nRF51822 SoC custom board on which i have successfully tried flashing the executable file using openocd commands over Linux environment...
After the rewrite of persistent storage in SDK For Mesh v4.0.0 the code no longer does any basic sanity checks on the data read back from the flash.
The code below is from...
Hi
I am evaluating the serial_lte_modem sample with pc as client but failed, could you share the cmd format for gps start function?
here is the log after I issued the...
Hi guys, I'm facing the next problem:
I am using the Android BLE Library and Android-nRF-Mesh libraries. I connect my Android application to 8 nodes. One of those nodes...
To perform dfu using nrfutil, we need to bring wpantund service down in order to provide serial port to nrfutil. That restrict me to communicate with end nodes. Can you please...
Hi Nordic people,
According to my knowledge SPI can not verify the bits whether it is properly sending or not(like ack),speed wise is SPI ok,And in nordic nRF52840 have...
Hi!
I'm trying to use the LIS2DH12 driver on SDK 16.0.0 in SES. I've managed to read the correct value of who am i register. I'm trying to configure the sensor using LIS2DH12_DATA_CFG...
I have set up 2 nrf52 dev kits: one central and one peripheral. The peripheral side hits the PM_EVT_CONN_SEC_FAILED event about 30 seconds after the connection was established...
I'm trying every permutation.
Pressing IF BOOT/RESET button along with BUTTON 4 and powering off and on the board ... then letting the buttons go
There is a reset...
Hello,
it would seem that the Spi Slave example provided with the SDK 12.3.0 does not work correctly for the nRF51DK. Setup:
Master SPI : STM30G070CB Slave SPI : nF51DK...
