I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi,
I've managed to code an app for nRF52382 (S132, SDK14) which works properly. Also, I've taken "bootloader_secure_serial" and removed a lot of stuff to code a simple...
To the kind attention of Nordic support team,
I've just downloaded a fresh copy of nRF5_SDK_16.0.0_98a08e2.zip.
I would like to download code in nRF52810. The code in...
I want to make a programmer for nrf52832. Do you know where is the documentation of SWD is ?
Note: I found the similar question, but the links are not active
Hi
I am using Segger Embedded Studio and SDK_v15.3.0. I have a C++ code that I wish to run on the board. It has a lot of printfs. I want to see the output of the print statements...
Hi,
I'm new to Nordic Semi chips (nrf52840) and need to use TWI as a master to connect to two sensors. But I'm a bit confused about the different drivers: TWI and TWIM....
Hello to all,
I have a problem related to the client side Global Attribute: I have implemented an "On / Off Switch" that presents the cluster On / Off (0x0006), client side...
Hello,
When we analyzing the traffic of our application (many thanks to the team developing the sniffer), we have several questions about sending write confirmation.
for...
We do have a product in which we program a bootloader on the target. It is remotely based on the ble_app_buttonless_dfu example. The bootloader is not actually used in the...
Hi I am building a software watchdog to monitor nrf52 peripheral states to have higher confidence for 10+ years battery lifetime. The idea is to check every few seconds if...
I am working with the S140 softdevice v6.1.0. The message sequence charts located on the Nordic infocenter are great help. Question: are they available in a printable form...
Hi,
Is there any editable software available that I can use to create a custom interface between my PC and my nrF58210 module. I have been successfully using the Nordic...
How to program flash with the output HEX file and SoftDevice file using NRF52-DK.
When programming with the output HEX file the device does not work, I need also HEX - SoftDevice...
I'm trying to set up a project with SDK 16.0.0 using FreeRTOS with the softdevice. The device will be battery powered and therefore power management capabilities are required...
Hi all,
I am trying to generally gain a better understanding of the GPIOTE module and how it can benefit myself in the project I am working on.
I am essentially attempting...
Hello
Does the nRF5280 include Schmitt-trigger inputs on the GPIO pins?
If yes, what are the voltage threasholds for the rising- / falling edges?
(Can't find anything...
