Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Is this a bug that is resolved in a particular softdevice version? If not, is there more information somewhere on this bug? How do i ensure that my code is robust against...
Are there examples of HW and SW to allow Power Amp, LNA, and TX/RX switch to be connected to the nRF52840_DK?
Or can you tell me what PIN on the chip or connector and pin...
Hello -
We are developing some low power code on the nRF52840-DK, using SDK 15.3.0 on FreeRTOS. I noticed that in the port_cmsys_systick.c file, in the vPortSuppressTicksAndSleep...
I am building a prototype that will use the nrf52840, with limited space. Would making a small pcb antenna or using a chip antenna be better and what is the setup needed for...
Hi,
I would like to measure the voltage generated by a Thermoelectric generator. The voltage vary between -250mV and 250mV depending on the temperature gradient.
If...
I'm looking for alternative xtal's (mhz + rtc) for use on boards where space is very limited.
Silego's GreenCLK3 looks like a great option, though that one is right now...
hi,
I want to use the Bluetooth Low Energy in nRF Connect for desktop. But I have no DK or dongle.
When I use my own development board and the MCU is nRF 52832, it can...
Hi
I am wondering how to choose among different logger mechanisms available in nRF SDK v16.0.
I noticed that some examples doesn't use any logger at all (e.g. blinky...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I have cleared the WDT with "nrf_drv_wdt_channel_feed". I want to make sure it is cleared. Which register can be used to confirm...
Hi I am using Keil ARM with JLINK to debug the NRF52832. I can download the flash on the PCBA but when I try to debug step-by step, it only runs on the assembly window but...
Hello ...
Implementing an app for both nRF51822 and nRF52810 and need a long-term clock with 100 Hz counter frequency to timestamp sensor events. By long-term, I mean at...
HI,
I've been looking at the nRF52811 registers for AoA/AoD, and decided to try and at least get CTE enabled on the basic Nordic uart app. I found this post:
https://devzone...
Hello. In acrording to:
How the bridge exchange information between mesh network and mobile device
The bridge using Nordic UART Service to conduct the command/response...
Struggling with a similar problem that has been popping up for many users. I am already stuck on setting up ncs where installation of pygit2 is failing. I managed to alleviate...
There is an SPIM unexpected interrupt issue which I have replicated in a totally bare-bones piece of code using no Nordic library drivers. In my bare-bones SPI code I get...
