SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I have set up the NCS toolchain, followed the instructions to update the JLink DLL in SES, and successfully built/flashed a few examples to the app core (ie. debug/ppi_trace...
I would like to send TCP message with 50KB message size. I saw that maximum size was limited by CONFIG_HEAP_MEM_POOL_SIZE which was 16kB.
Is there any way to send that message...
Hi,
we are experiencing unexpected behavior during sleep entry. Following pictures were taken using an oscilloscope, our device sends a radio transmission every 150 ms...
Hello,
I am trying to sample and reconstruct an audio signal using the SAADC and I2S respectively. I have a double buffer setup for the SAADC, where we process the data...
Hi,
I've noticed several times now when the NRF9160 comes out of a PSM sleep cycle that when a call to an underlying socket connect(), or nrf_getaddrinfo() call (whether...
HI,
I am developing an application with 7 transmitters and 1 receivers. Transmitter are nrf52832 with MPU9250 IMU (Holyiot YJ-18008) . I am hopping to each transmitter...
I successfully compiled and loaded the UART/Serial Port Emulation over BLE example on an AdaFruit Feather board.
I can connect to the Nordic UART Service, then send data...
I have built my application on ble_app_uart in keil in SDK 14, so I just did the same and copy-pasted my code into the latest ble_app_uart example built with ses in SDK 16...
So far i've failed to find a single source that contains comprehensive information on where errata items have been addressed. I do have multiple unrelated sources for information...
Hello, I want to try the secure bootloader + softdevice 7.0.1 + ble app buttonless dfu example from SDK16 I want to test all that in our custom board NRF52832-QFAB (256k flash...
Hello, I modified the ble_app_blinky example to work on our board (removed leds and buttons) and modified the board pca10040.h the new application worked on the devkit but...
Hello, I am completely new to embedded software development (so far I have been using development boards such as Teensy, Feather and Arduino) and I recently acquired the BLYST...
Hi
I'm currently look into the noise floor of the SAADC samples on a custom PCB with a nRF52
I'm running the ADC at maximum sensitivity (4x gain, Vref=0.6V) differential...
Hello
I have a power constraint device. Limit is not the total charge of a battery or so. Limit is the peak current.
Available (peak) current is around 4mA (@1.8V), current...
Hi,all. i face a problem that i used lightblue on iphone6(ios8.3 12F70) to connect my device(nRF51822),after sometime,disconnected automatic.
lightblue says:The connection...
