This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi, I have custom nRF52832QFAAE1 when I tried to run Peripheral applications which are working fine. whereas BLE applications are not running it seems.
here are the things...
Hello,
When I clean a project and do a new build, parallel settings looks wring (my AMD ryzen 3900X with 12 cores never use more than 40 %).
Do someone have a setting...
Currently, we are testing the nRF52840 range evaluation using the nRF52840 EVK kit.
As of now, we are getting the only 120 to 125-meter range using 125kbps data rate @ 4dBM...
Hello.
I found in Provisioing chapter on this document: https://www.bluetooth.com/specifications/mesh-specifications/
something like list of provisioning commands: ...
Hello.
I plan to perform antenna matching to improve the performance of my design.
I would like to know any differences when performing the match on bare pcb and pcb...
Hi,
I'm working on a test for the pulse width measurement, the input is analog signal.
I'm using a while loop, and use nrfx_comp_sample in the loop to get the voltage...
Hi All,
I just start to use the Thingy 52 and I would like to know if there is any source code for development purpose for Windows. Also, which development software does...
in SDK/examples/peripheral/blinky/ hex
there is one file
blinky_pca10056 _mbr .hex
in
SDK/examples/peripheral/blinky/pca10056/ mbr /ses/Output/Release/Exe
there...
Hi
I am very new to BLE...
We are looking into a new industrial product design that will be battery powered, and be capable of communicating with BLE sensors (Mesh not...
Hi!
My software setup consists of SDK 15.0.0 and SD 6.0.0.
I am using nRF52DK for flashing and debugging my custom PCB board on nRF52832.
I am developing an application...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) At factory first we will load Secure Serial Bootloader and SoftDevice...
We are building a prototype for a wireless solution using nRF52840 and we found that the UART included in this MCU does not support Odd parity. This is a major handicap that...
Hello, I am writing a Program where I use GPS and NBIoT. Recently, I wanted to combine the default GPS example code with an NBIoT Code, that connects to a TCP Server and when...
Hi,
We are using Eclipse editor for nRF52833 SDK 16.0. While searching GDB support for nordic devices i found following link
https://devzone.nordicsemi.com/nordic/nordic...
Hello,
I am using the nrf9160 and I am developing using zephyr. I have an nrf connect project in Segger IDE.
Generally I am able to edit and build my project. The problem...
