I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
I am evaluating nrf52840 using the light switch example.
Environment:
Soft device : s132_nrf52_6.1.1
Mesh SDK Version: 3.2.0
SDK Version: 15.3.0
IDE: SES ...
Hello!
I currently want to save the sensor data obtained by SPI communication to the microSDHC card by SPI communication.
Writing to the SDHC card is possible without...
To the kind attention of Nordic support team,
I'd like to open a new thread after the first one ( https://devzone.nordicsemi.com/f/nordic-q-a/46318/configuration-of-gzp_dynamic_pairing...
I have been using Power Profiler Kit nRF6707 for awhile without problem.I made a mistake by downloading firmware when the PPK is attached to nRF52 DK, the software on the...
Hi all
The iC is not advertising , neither it is able to get programmed.
The voltage levels are ok. It is getting sufficient Voltage at its o/p and delivering o/p at DEC...
Hi,
Please help to share Memory size of following SoftDevices:
S112
S113
S132
S140
Also, what will be the memory size of SoftDevice if i implement Central +...
Hi,
We are migrating from 12.3 SDK version to 15.3 version.
We observed the almost 22 KB of RAM is reserved. Where as in 12.3SD version we don't see this.
We are still...
Hi,
our company one new product using you nRF52832. We already prepared everything for CE (RED ) and FCC certification process. Only thing that is unclear is Bluetooth SIG...
Hi!
I am currently using SEGGER Embedded Studio version 4.12, nRF5 SDK version 15.2.0, nRF5 SDK for Mesh version 3.1.0, Hardware BMD-300 Evaluation Board.
i using the...
I need to measure a load-cell bridge. Although, I'm fairly certain I'd be better off with an external delta-sigma ADC with an internal amplifier - I'd like to run through...
Hi,
I study on Thread resently.
I found it is not any output in the Debug Terminal Window when using NRF_LOG_XXX, but the J-link Control panel showed the logs.
Here...
Hi,
I am trying USB DFU trigger.
I have connected GPIO P024 to Reset port P018.
Bootloader is also programmed.
When I use nRF connect/programmer.
It's always waiting...
My system: MacBook Air with macOS 10.14.6, Xcode 10.3, with sdk at /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.14.sdk
When...
