According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi.
I am trying to update soft_device version 6.0.0 to 7.0.1.
I read that because of the major version change (from 6 to 7), i must update the bootloader as well.
I...
Hi,
I am prototyping with the the THINGY52 using nRF Connect.
I am using the services available to drive the MOSFETs on the expansion connector P4 through the services...
Hi,
I would like to debug the code which is in Nordic Thingy91 by using nRF52840DK.
Is it possible to use the debugger in nRF52840DK for Nordic Thingy91 ?
If it is possible...
Hi,
I like to understand what SBs should I cut, what switched should I use to measure the SOC current only with PCA10056 board. I use the Otii Arc device to supply power...
Hello,
I'm working on NRF52832 based module BMD-301
for same i'm using SDK16 Segger Embedded Studio
The thing is
when uploaded ble_app_alert_notification example it...
Hello,
I've tried to convert the mesh light switch server example from NRF52840 DK to Dongle following this post.
Unfortunately that doesn't work.
I've changed the BOARD_PCA10056...
Currently, there is a project. The situation is that the master nRF52840 communicates with the cloud server through the GPRS232 module, the slave nRF52840 communicates with...
Hi,
I tried to create a custom server in using server setup of nRF Connect v3.3.0 but when I tried to apply my custom server on my device, the software bugs instantly. ...
I want to modfiy the code in the example ble_app_ancs_c to read the internal flash with fstorage. But after I set APP_TIMER_CONFIG_USE_SCHEDULER to 1, the operation of fstorage...
Hi every one, I am running light switch example (using SDK 15.2 and SDK for Mesh version 3.1.0 ). The problem is: My provisioner node cannot Receive RSSI message of a node...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
My custom function for saving is:
I call the function using below...
This error always stop the "mqtt_simple" application.
I have tried modem versions 1.0.1 and 1.1.0, SDK versions v1.0.0 and v1.1.0 and added this code to system_nrf9160.c...
I have an Android application running with RxAndroidBle library and I want to change it to Nordic-Ble-Android library. I'm not that good with Bluetooth and the actual version...
Hello, i'm new in BLE and i would like to know, what is the best way to read and write 200-300 parameters of my product via BLE from a phone?
Possibility 1 is, to create...
I am trying to save and read a structure using FDS, how do I go about it?
I have the structure:
Is this correct by populating the record as such?:
And to read...
