Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
As you can see in the schematic, I have a custom board, and I’m uploading code to it via J-Link. I can control the pins, turn on an LED, and read a button without any problems...
I am working on project using thenRF9151 board and I require the GNSS functionality to work for the same. However, my board is not able to latch on to a satellite network...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
I have a project that I need to use most of the GPIO pins available on the nRF52840 DK. I'm using SDK V17.
I'm writing a test program that toggles all GPIO pins on an nRF52840...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
