Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi,
i am using blend micro with nRF8001 .. i want to make the bluetooth module to sleep on an interrupt such that it should consume the lowest power.
thanks in advance.
I want to use Seggers RTT for data logging.. but after 199lines the Viewer starts to overwrite the old lines.. so that only the most recent 199 lines are displayed..
Are...
Hello,
I want to use nRF8001,but I'm a beginner for nRF8001,I have no idea how to start my software design.
Could anybody give me some guide about how to start my design...
Hello Everyone
i have been trying to implement the pwm library from the GITHUB inorder to make the buzzer beep sound but after compilation it is showing these two errors...
i want to add a characteristic readable that hold a device TimeCount; timeCount is increasing;
ble client (andorid) can read the characteristic at any time;
how can...
Hello,
I'm going to start a new design based on the CSP 3.0 x 3.2 package for nRF52832 (CEAA version), I already find the reference information for the QFN 6.0 x 6.0 package...
First I want to mention, that I know about the pwm inverted issue.
About my project:
I have a switch which will start and stop a pwm signal. And I use a softdevice,...
Is it possible that one nRF51 implement communication Bluetooth LE or 2.4 GHz RF communications (eg. From nRF24), and switch between via external button?
Hi!all:
I used nrf51822 to connect with iPad mini3,and if I turnoff the iPad mini3 panel ,does the iPad mini3 will send
BLE suspend command or any others to nrf51822 ? If...
Hi,
I wan to load ble_app_hrs_s110_pca10028 project example from SDK 8.10 to a module purchased on eBay:
www.ebay.com/.../111600483137
This module has nrf51822 qfaag2...
Hi all,
I want to implement homekit stack on nRF51 device and I am stuck with service instance id (UUID = 00000051).
When I create a standard service like hrs I don't...
How can I do that? Which pin is available for this?I am trying to controlled with my smart phone due to an application which i design,how can i import this part to my original...
Hi,
I'm using S130 with PCA10028 and I would like to connect my central device to multiple peripheral at the same time.
According to my understanding, the only way I...
Hello everybody,
we want to extend out Central device to dual role (Central + Peripheral). I just finished the migration to SoftDevice S130 and was about to migrate the...
Are there any laws or regulatory certifications that state a wireless or Bluetooth device must be able to power off or at least stop transmitting through user action? Can...
